Magnavox TB100MG9 owner manual Others, Troubleshooting

Page 30

Others

Troubleshooting

Before requesting service, check the table below for a possible cause of the problem.

Symptom

Remedy

	No power	•	Make sure that the AC power cord is securely plugged into the power
	No power		outlet.
			outlet.

		• Make sure to point the remote control at the remote control sensor.
		• You may be too far from STB. Try moving closer.
	The STB is not responding	• Remove any obstacles between the remote control and the remote
	The STB is not responding		control sensor.
	to the remote control.		control sensor.
	to the remote control.	• Make sure that the batteries are installed in the correct direction

			(+ and –). ( Page 7.)
		• The batteries may be depleted. Replace them with new ones.
		• Make sure that the audio / video cables are correctly connected.
		• Make sure that the TV is turned on.
	No audio / picture	• Make sure that the correct viewing channel (ch3 or external input
	No audio / picture		channel) is selected on your TV. ( Page 13.) Refer to your TV’s manual
			for further information.
		• Make sure the cables are not damaged.
		•	Make sure “RF OUT” setting is correct. ( Page 29.)
	Blocked noise on picture	•	Make sure that the RF cable is connected correctly. (	Pages 10 - 12.)
	No EPG or the provided	•	Make sure that “D.S.T” and “TIME ZONE” is set correctly. ( Page 21.)
	information is wrong
	Low volume	•	Sound volume differs depending on the audio out setting. Select “RF
	Low volume		OUT” at step 5 in the “Initial Setup (Setup Wizard)”. (	Page 14.)
			OUT” at step 5 in the “Initial Setup (Setup Wizard)”. (	Page 14.)
		• Make sure to complete autoscan in “SETUP WIZARD” or in “SETUP”
			menu. When autoscan is not completed, some channels will not be
		•	received.
	No reception	•	The selected channel does not exist at that time. There are not always
			sub-channels being broadcast.
		• Some channels with weak signal may not be received properly.
			This is not a malfunction.
	When you forget the	•	If you forget the password, refer to “New Password”. (	Page 24.)
	password for V-chip
	Closed captioning display	•	Change the channel on your TV.
	(TEXT mode) does not go	•	Turn the TV off, and then on.
	off even after changing
	channels through STB.

	The TV screen goes blank	•	This is a normal part of the start-up process and is not a malfunction.
	just after turning the STB
	on.

30

EN

Image 30

Contents TB100MG9 Before Using Risk of Electric Shock Do not OpenInsert Precautions Important Copyright InformationBefore Using Advanced Operation B l e o f C o n t e n t sOverview Accessories Installing BatteriesInformation on Digital Broadcasting Remote Control Location of ControlsRear Panel Remote control sensor Power indicatorFront Panel Video OUT jack yellowConnections Connecting to a TV without A/V JacksConnecting to a TV with A/V Jacks White red YellowRed Connecting to a Cable Box OptionalWhite EllowConnecting to Other Devices Red yellowPress STANDBY-ON on the remote control to activate the STB Initial Setup Setup WizardInitial Setup Appropriate Viewing ChannelSelect your time zone using K / L, then press OK Select Continue using s / B, then press OKSelect the language using K / L, then press OK Select Autoscan using K / L, then press OKAbout Sub-channel Broadcasting Basic OperationSelecting Channels on the STB Enter the main channel numberPress Still To cancel still modePress Audio repeatedly Choosing Audio LanguagePress EPG while watching TV Select the desired program using s / BPress Display Channel BannerAdvanced Operation Press SetupSelect ADD/ Delete using K / L, then press OK Autoscan Receiving ChannelsPress OK again to add the channel to the channel map Press Setup to exitSelect Delete using K / L, then press OK AddPress Setup Select Detail using K / L, then press OK Adjusting AntennaSelecting Display Mode SelectDISPLAY MODEusing K / L, then press OKPress Setup Select Time using K / L , then press OK Information on Display ModeSetting the Time Zone and D.S.T Daylight Saving Time Select Time Zone using K / L , then press OKEnter the password using the Number buttons Select D.S.T using K / L , then press OKSelect on or OFF using s / B , then press OK Chip OptionsThen press OK repeatedly to switch between view and block Select the desired rating type using K / L , then press OKSelect the desired rating using Mpaa RatingSelect NEW Password using K / L , then press OK Enter the new 4-digit password using the Number buttonsSelect Closed Caption using K / L , then press OK Press Setup Select Detail using K / L , then press OKSelect Manual using K / L , then press OK Closed Caption OptionsAuto Power Down Select desired amount of time using K / L , then press OKSelect CH3 in RF OUT menu Viewing Analog TVMethod 1 Método Select ch3 on your TVSelect the desired channel on your TV Method 2 MétodoSelect RF Through in RF OUT Press STANDBY-ON to activate the STBSelect RF OUT using K / L, then press OK Setting RF OUTUsing Setup to Switch RF OUT Setting Select the desired setting using K / L, then press OKTroubleshooting OthersSpecifications Limited Warranty Customer Service Tel