Magnavox TB100MG9 owner manual Adjusting Antenna, Selecting Display Mode

Page 20

Advanced Operation

Adjusting Antenna

You can verify the signal strength of each channel.

1Select a channel to adjust using [the Number buttons] or [CH K / L].

2 Press [SETUP].

3Select “CHANNEL” using [ K / L], then press [OK].

4Select “ANTENNA” using [ K / L], then press [OK].

CHANNEL

EXIT		ADD/DELETE
CHANNEL
		ANTENNA
TIME		ADD/DELETE

DETAIL		RF OUT

INITIAL

•STB starts receiving the signal for the channel.

5By referring to the on-screen indication, adjust the antenna’s direction to get the best reception.

Status bar:

Stretches to the right as the signal strength gets stronger.

ANTENNA		10.1
		10.1
EXIT	WEAK	STRONG
	WEAK	STRONG
CHANNEL	NOW
TIME	10
TIME		50
		50
DETAIL	BACK	PEAK
DETAIL

INITIAL

Peak indicator:

Indicates the highest strength ever reached.

To adjust other channels:

Select the channel using [CH K / L], then adjust it.

6 Press [SETUP] to exit.

Selecting Display Mode

You can adjust the aspect ratio of the digital TV program to fit your 4:3 TV monitor.

Display Mode

1 Press [SETUP].

2Select “DETAIL” using [ K / L], then press [OK].

SETUP

EXIT
EXIT		V-CHIP
CHANNEL		V-CHIP
CHANNEL		CLOSED CAPTION
		CLOSED CAPTION
TIME		DISPLAY MODE	LETTERBOX
DETAIL		DISPLAY MODE	LETTERBOX
DETAIL		AUTO POWER DOWN		4 HOURS
INITIAL

3Select“DISPLAY MODE”using [ K / L], then press [OK].

DETAIL

	EXIT		V-CHIP
	CHANNEL		V-CHIP
	CHANNEL		CLOSED CAPTION
			CLOSED CAPTION
	TIME
			DISPLAY MODE		LETTERBOX
	DETAIL		AUTO POWER DOWN
	DETAIL		AUTO POWER DOWN			4 HOURS
	INITIAL

4Select the desired display mode using [ K / L], then press [OK].

* Descriptions of each settings are explained in the “Information on Display Mode” on the next page.

Select display mode.

LETTERBOX

ZOOM

FULL

5 Press [SETUP] to exit.

20

EN

Image 20

Contents TB100MG9 Before Using Risk of Electric Shock Do not OpenInsert Precautions Important Copyright InformationBefore Using Advanced Operation B l e o f C o n t e n t sOverview Information on Digital Broadcasting AccessoriesInstalling Batteries Remote Control Location of ControlsRemote control sensor Power indicator Front PanelRear Panel Video OUT jack yellowConnecting to a TV without A/V Jacks Connecting to a TV with A/V JacksConnections White red YellowConnecting to a Cable Box Optional WhiteRed EllowConnecting to Other Devices Red yellowInitial Setup Setup Wizard Initial SetupPress STANDBY-ON on the remote control to activate the STB Appropriate Viewing ChannelSelect Continue using s / B, then press OK Select the language using K / L, then press OKSelect your time zone using K / L, then press OK Select Autoscan using K / L, then press OKBasic Operation Selecting Channels on the STBAbout Sub-channel Broadcasting Enter the main channel numberTo cancel still mode Press Audio repeatedlyPress Still Choosing Audio LanguageSelect the desired program using s / B Press DisplayPress EPG while watching TV Channel BannerPress Setup Select ADD/ Delete using K / L, then press OKAdvanced Operation Autoscan Receiving ChannelsPress Setup to exit Select Delete using K / L, then press OKPress OK again to add the channel to the channel map AddAdjusting Antenna Selecting Display ModePress Setup Select Detail using K / L, then press OK SelectDISPLAY MODEusing K / L, then press OKInformation on Display Mode Setting the Time Zone and D.S.T Daylight Saving TimePress Setup Select Time using K / L , then press OK Select Time Zone using K / L , then press OKSelect D.S.T using K / L , then press OK Select on or OFF using s / B , then press OKEnter the password using the Number buttons Chip OptionsSelect the desired rating type using K / L , then press OK Select the desired rating usingThen press OK repeatedly to switch between view and block Mpaa RatingSelect NEW Password using K / L , then press OK Enter the new 4-digit password using the Number buttonsPress Setup Select Detail using K / L , then press OK Select Manual using K / L , then press OKSelect Closed Caption using K / L , then press OK Closed Caption OptionsAuto Power Down Select desired amount of time using K / L , then press OKViewing Analog TV Method 1 MétodoSelect CH3 in RF OUT menu Select ch3 on your TVMethod 2 Método Select RF Through in RF OUTSelect the desired channel on your TV Press STANDBY-ON to activate the STBSetting RF OUT Using Setup to Switch RF OUT SettingSelect RF OUT using K / L, then press OK Select the desired setting using K / L, then press OKTroubleshooting OthersSpecifications Limited Warranty Customer Service Tel