Magnavox TB100MG9 owner manual Viewing Analog TV, Method 1 Método, Select CH3 in RF OUT menu

Page 27

Viewing Analog TV

Viendo TV Analógica

Method 1 Método 1

You can view analog TV by switching “RF OUT” setting.

Usted podrá ver TV analógica cambiando la configuración de “SALIDA RF”.

CONNECTION

CONEXIÓN

TV

STB

TV antenna

Antena de TV

RF cable (supplied)

cable de RF (se incluye)

Viewing Analog TV

Viendo TV Analógica

1 Press [STANDBY-ON] to activate the STB.

Presione [STANDBY-ON] para activar el STB.

2 Select “RF THROUGH” in “RF OUT”

menu. ( Page 29)

Seleccione“TRAVÉS DE RF”en el menú“SALIDA RF”.

3 Select the desired channel on your TV.

Seleccione el canal deseado en su TV.

ch4

ch6

ch8

You can view analog TV on your TV channel.

Usted podrá ver TV analógica en su canal de TV.

NOTE:

•You cannot view Digital TV with this setting.

•With this setting, the analog TV signal can directly be sent to your TV.

Viewing Digital TV

Viendo TV Digital

1 Press [STANDBY-ON] to activate the STB.

Presione [STANDBY-ON] para activar el STB.

2 Select “CH3” in “RF OUT” menu.

( Page 29)

Seleccione “CH3” en el menú “SALIDA RF”.

3 Select ch3 on your TV.

Seleccione canal3 en su TV.

ch3

You can view digital TV on ch3 of your TV.

Usted podrá ver TV digital en el c3 de su TV.

4 Select desired channel on the STB.

Seleccione el canal deseado en el STB.

ch3

ch3

ch3

NOTE:

•You cannot view Analog TV with this setting.

•You can switch “RF THROUGH” to “CH3” by holding [SET UP] down over 3 seconds.

Holding [SETUP] down over 3 seconds does not switch the setting back to “RF THROUGH”.

27	To switch the setting back to “RF THROUGH”, follow
	the steps in “Setting RF OUT” on page 29.

Operation	Advanced

EN

Image 27

Contents TB100MG9 Risk of Electric Shock Do not Open Before UsingInsert Important Copyright Information PrecautionsB l e o f C o n t e n t s Before Using Advanced OperationOverview Accessories Installing BatteriesInformation on Digital Broadcasting Location of Controls Remote ControlVideo OUT jack yellow Remote control sensor Power indicatorFront Panel Rear PanelWhite red Yellow Connecting to a TV without A/V JacksConnecting to a TV with A/V Jacks ConnectionsEllow Connecting to a Cable Box OptionalWhite RedRed yellow Connecting to Other DevicesAppropriate Viewing Channel Initial Setup Setup WizardInitial Setup Press STANDBY-ON on the remote control to activate the STBSelect Autoscan using K / L, then press OK Select Continue using s / B, then press OKSelect the language using K / L, then press OK Select your time zone using K / L, then press OKEnter the main channel number Basic OperationSelecting Channels on the STB About Sub-channel BroadcastingChoosing Audio Language To cancel still modePress Audio repeatedly Press StillChannel Banner Select the desired program using s / BPress Display Press EPG while watching TVAutoscan Receiving Channels Press SetupSelect ADD/ Delete using K / L, then press OK Advanced OperationAdd Press Setup to exitSelect Delete using K / L, then press OK Press OK again to add the channel to the channel mapSelectDISPLAY MODEusing K / L, then press OK Adjusting AntennaSelecting Display Mode Press Setup Select Detail using K / L, then press OKSelect Time Zone using K / L , then press OK Information on Display ModeSetting the Time Zone and D.S.T Daylight Saving Time Press Setup Select Time using K / L , then press OKChip Options Select D.S.T using K / L , then press OKSelect on or OFF using s / B , then press OK Enter the password using the Number buttonsMpaa Rating Select the desired rating type using K / L , then press OKSelect the desired rating using Then press OK repeatedly to switch between view and blockEnter the new 4-digit password using the Number buttons Select NEW Password using K / L , then press OKClosed Caption Options Press Setup Select Detail using K / L , then press OKSelect Manual using K / L , then press OK Select Closed Caption using K / L , then press OKSelect desired amount of time using K / L , then press OK Auto Power DownSelect ch3 on your TV Viewing Analog TVMethod 1 Método Select CH3 in RF OUT menuPress STANDBY-ON to activate the STB Method 2 MétodoSelect RF Through in RF OUT Select the desired channel on your TVSelect the desired setting using K / L, then press OK Setting RF OUTUsing Setup to Switch RF OUT Setting Select RF OUT using K / L, then press OKOthers TroubleshootingSpecifications Customer Service Tel Limited Warranty