Extron electronic DDS 402 manual Input #2 submenu, Pixel Phase submenu, Output Configuration menu

Page 26

Operation, cont’d

Display Menu

 

Input

 

Next

 

Input #2

 

Next

 

 

 

 

Cycle

 

Configuration

 

 

 

Betacam 50

 

 

1 2

Input #2 Phase NEXTNext

016

The selected input is also available for the pixel phase adjustment (next screen).

Input video type

Use either Adjust

• RGB

• Betacam 50

knob to set the

•

YUVi

•

Betacam 60

slected output’s

•

YUVp

•

HDTV

pixel phase.

Figure 3-5 — Input Configuration menu flowchart

If you press the Menu button while a main menu or a submenu is active, the next main menu becomes active. For example, the display changes from the Input Configuration main menu or the Input #2 submenu to the Output Configuration main menu.

To return to the default screens, let the DDS 402 remain idle for 10 seconds until the selected screen times out, or press the Menu button until the Exit Menu appears, then press the Next button.

Input #2 submenu

Rotate either the Adjust or the Adjust knob while in the Input #2 submenu to select the correct video format (RGB, YUVi, YUVp, Betacam 50, Betacam 60, or HDTV) for input 2. The default for input 2 is Betacam 60.

Pixel Phase submenu

The Pixel Phase submenu displays and lets you set the pixel phase for the selected input. Pixels phase is the timing of the digital scaler’s sampling. Sampling at the optimum pixel phase reduces noise and results in a clear and sharp image.

Rotate either the Adjust or the Adjust knob to select the pixel phase for the selected input from 0 to 31. You can select the unselected input while this screen is active by pressing the desired Input button. The default is 16.

The pixel phase adjustment for input 2 is only available when the input type is set to RGB, YUVp, or HDTV.

Output Configuration menu

Figure 3-6 is a flowchart that shows an overview of the Output Configuration menu, the submenus, and the available settings.

Input

Configuration

MENU

Output

Configuration

MENU

Memory

Presets

NEXT

Resol 1024 x 768

NEXT

Output Signal

NEXT

Sync Polarity

 

NEXT

Refresh @ 60

RGB

H Neg

V Neg

 

 

 

 

Scaler output resolutions

Scaler output frequencies

Output signal format

 

Polarity combinations

See the table on the

NOTE Lock = Accu-RATE

• RGB

 

• H-/V- (default)

•

H+/V-

opposite page for available

 

Frame Lock™

• Y, R-Y, B-Y

 

• H-/V+

 

•

H+/V+

combinations of resolutions and refresh rates.

Default: 1024x768, 60 Hz

Figure 3-6 — Output Configuration menu flowchart

3-6 Digital Display Scaler • Operation

Page 25 Page 27
Image 26
Page 25 Page 27
Contents DDS Digital Display ScalerSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolRear panel video outputs QS-1Main menu Input menu Default display cycleQuick Start DDS 402, cont’d QS-2QS-3 Memory Presets menuOutput menu Executive Mode menu Advanced Configuration menuPicture Adjustments menu Exit menuTable of Contents Table of Contents, cont’d Digital Display Scaler Table of Contents Iii Iv Digital Display Scaler Table of Contents One About the Scaler Introductiontroduction, cont’dAbout this Manual Digital Display Scaler IntroductionFeatures Introduction, cont’d Digital Display Scaler Introduction Introduction, cont’d Two Mounting the Scaler Installationstallation, cont’dInstallation Overview Cabling and Rear Panel ViewsVideo input connections Video output connectionsPower connection Installation, cont’dConfiguration RS-232 connectionThree Freeze button Front Panel Controls and IndicatorsOperationeration, cont’d Input buttonsLCD display Picture adjustment buttonsAdjustment knobs Menu control buttonsFront Panel Operations PowerOperation, cont’d Button iconsConfiguration Input Configuration menuInput #2 submenu Pixel Phase submenuOutput Configuration menu Output Signal submenu Resolution and refresh rates submenuResolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 Hz Sync Polarity submenuSave Presets submenu Erase Presets submenuEdge Smoothing submenu Blue Mode submenuRGB Delay submenu Test Pattern submenuPicture adjustments Reset submenuFront panel security lockout executive mode Adjust knobs have no mechanical limits to their rotationSetting up a DVD source Optimizing the VideoFour Symbols Digital Display Scaler Programmer’s GuideScaler-Initiated Messages Programmer’s Guide, cont’d RGB delayPresets Test patternHost-to-Scaler Instructions Scaler Error ResponsesUsing the Command/Response Table Command/response table for SIS commands Command Ascii Command Response Additional descriptionCommand/response table for SIS commands cont’d Test pattern Command/response table for special function SIS commands Command Ascii Command ResponseProgrammer’s Guide, cont’d Five Control Software for Windows Installing the softwareUsing the control program Digital Display Scaler Scaler SoftwareUsing the help program Control program I/O configuration windowButton Label Generator Using the softwareScaler Software, cont’d AAppendix a Specifications Digital Display Scaler Reference InformationSuggested part Part NumbersIncluded parts Included parts Part numberFirmware Upgrade Installation Reference Information, cont’dU24 U60 U68U67 Installing labels in the scaler’s buttons Button LabelsFCC Class a Notice Extron’s Warranty Extron Electronics, USA
Related manuals
Manual 2 pages 53.37 Kb
Top Page Image Contents