Extron electronic DDS 402 manual Command/response table for SIS commands

Page 38

Programmer’s Guide, cont’d

Command/response table for SIS commands

Command

ASCII Command

Response

Additional description

(host to scaler)

(scaler to host)

Input selection

Select video input

X1

!

In•

X1

All

Select video input

X1

.

Example:

2!

In•2All

Select video input 2.

Select video input

&

In•

Vid

Select video input

.

X1

X1

X1

Read video input

!

X1

Video input

X1

is selected.

Read video input

&

Video input

is selected.

X1

X1

Input 2 video type

Set video type, input 2 only

X2

\

Typ

X2

Specify input 2 video type.

Example:

3\

Typ3

Specify input 2 type as YUVp.

View video type

\

Input 2 video type is

.

X2

X2

Scaler output rate

Set the output rate

X3

*

X4

=

Rte

X3

*

X4

Select a scaler output scan rate.

View the output rate

=

*

Show the scaler output rate.

X3

X4

Example:

=

01*02

The scaler is outputting 800x600

at 60 Hz.

Brightness

Set a specific value

X8

Y

Brt

X8

Specify the brightness

adjustment.

Increment

+Y

Brt

Increase the brightness.

X8

Decrement

–Y

Brt

X8

Decrease the brightness.

View the brightness value

Y

Show the brightness setting.

X8

Contrast

Set a specific contrast value

X9

^

Con

X9

Specify the contrast adjustment.

Increment

+^

Con

Increase the contrast.

X9

Decrement

–^

Con

X9

Decrease the contrast.

View the contrast value

^

Show the contrast setting.

X9

Zoom

Zoom in

+{

Zom

Zoom in.

Zoom out

–{

Zom

Zoom out.

Horizontal centering

Increment

+H

Hph

Shift right.

Decrement

–H

Hph

Shift left.

Vertical centering

Increment up

+*/

Vph

Shift up.

Increment down

–*/

Vph

Shift down.

Horizontal size

Increase the horizontal size

+:

Hsz

Widen the picture.

Decrease the horizontal size

–:

Hsz

Make the picture narrower.

Vertical size

Increase the vertical size

+;

Vsz

Make the picture taller.

Decrease the vertical size

–;

Vsz

Make the picture shorter.

4-6 Digital Display Scaler • Programmer’s Guide

Image 38

Contents DDS Digital Display ScalerSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolRear panel video outputs QS-1Main menu Input menu Default display cycleQuick Start DDS 402, cont’d QS-2QS-3 Memory Presets menuOutput menu Executive Mode menu Advanced Configuration menuPicture Adjustments menu Exit menuTable of Contents Table of Contents, cont’d Digital Display Scaler Table of Contents Iii Iv Digital Display Scaler Table of Contents One About the Scaler Introductiontroduction, cont’dAbout this Manual Digital Display Scaler IntroductionFeatures Introduction, cont’d Digital Display Scaler Introduction Introduction, cont’d Two Mounting the Scaler Installationstallation, cont’dInstallation Overview Cabling and Rear Panel ViewsVideo input connections Video output connectionsPower connection Installation, cont’dConfiguration RS-232 connectionThree Freeze button Front Panel Controls and IndicatorsOperationeration, cont’d Input buttonsLCD display Picture adjustment buttonsAdjustment knobs Menu control buttonsFront Panel Operations PowerOperation, cont’d Button iconsConfiguration Input Configuration menuInput #2 submenu Pixel Phase submenuOutput Configuration menu Output Signal submenu Resolution and refresh rates submenuResolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 Hz Sync Polarity submenuSave Presets submenu Erase Presets submenuEdge Smoothing submenu Blue Mode submenuRGB Delay submenu Test Pattern submenuPicture adjustments Reset submenuFront panel security lockout executive mode Adjust knobs have no mechanical limits to their rotationSetting up a DVD source Optimizing the VideoFour Symbols Digital Display Scaler Programmer’s GuideScaler-Initiated Messages Programmer’s Guide, cont’d RGB delayPresets Test patternHost-to-Scaler Instructions Scaler Error ResponsesUsing the Command/Response Table Command/response table for SIS commands Command Ascii Command Response Additional descriptionCommand/response table for SIS commands cont’d Test pattern Command/response table for special function SIS commands Command Ascii Command ResponseProgrammer’s Guide, cont’d Five Control Software for Windows Installing the softwareUsing the control program Digital Display Scaler Scaler SoftwareUsing the help program Control program I/O configuration windowButton Label Generator Using the softwareScaler Software, cont’d AAppendix a Specifications Digital Display Scaler Reference InformationSuggested part Part NumbersIncluded parts Included parts Part numberFirmware Upgrade Installation Reference Information, cont’dU24 U60 U68U67 Installing labels in the scaler’s buttons Button LabelsFCC Class a Notice Extron’s Warranty Extron Electronics, USA

Related manuals

Manual 2 pages 53.37 Kb