Extron electronic DDS 402 manual Specifications, Digital Display Scaler Reference Information

Page 48

Reference Information

Specifications

Video input

Number/signal type	1 RGBHV, RGBS, RGsB
	1 RGBHV, RGBS, RGsB, component video
Connectors	(1) 15-pin HD female
	5 BNC female
Nominal level	1 Vp-p for Y of component video
	0.7 Vp-p for RGBfor R-Y and B-Y of component video
Minimum/maximum levels	Analog: 0.0 V to 2.0 Vp-p with no offset
Impedance	75 ohms
Horizontal frequency
RGB	Autoscan 24 kHz to 100 kHz
Video	PAL/NTSC 3.38/NTSC 4.43/SECAM
Vertical frequency	Autoscan 50 Hz to 120 Hz
Resolution range	Autoscan 560 x 384 to 1600 x 1200

Video processing

Digital sampling	24 bit, 8 bits per color; 140 MHz standard, 200 MHz zoom
Colors	16.8 million
Horizontal filtering	4 levels
Vertical filtering	8 levels

Video output

Number/signal type	2 identical outputs:
	1 RGBHV, HD component (Y, R-Y, B-Y) (on 15-pin HD)
	1 RGBHV, RGBS, HD component (Y, R-Y, B-Y) (on BNCs)
Connectors	(1) 15-pin HD female
	6 BNC female
	(1) 15-pin HD female (buffered local monitor output)
Nominal level	1 Vp-p for Y of component video
	0.7 Vp-p for RGB and for R-Y and B-Y of component video
Minimum/maximum levels	0.0 V to 1.0 Vp-p
Impedance	75 ohms
Scaled VGA resolution	640x480, 800x600, 832x624, 848x480, 852x480, 1024x768, 1280x768, 1280x1024,
	1360x765, 1360x1024, 1400x1050, 576p, 720p, 1080p, and 1080i
DC offset	±50 mV (max) with input at 0 offset
	(for R, G, B, and for Y of component video)
	350 ± 25 mV (max) with input at 0 offset (for R-Y, B-Y of component video)

Sync

Input type	RGBHV, RGBS, RGsB
Output type	RGBHV, RGBS
Standards	NTSC 3.58, NTSC 4.43, PAL, SECAM
Input level	0.0 V to 5.0 Vp-p
Output level	0.0 V to 5.0 Vp-p
Input impedance	75 ohms
Output impedance	510 ohms
Max input voltage	5.0 Vp-p
Polarity	RGBS: negative
	RGBHV: user-selectable

A-2 Digital Display Scaler • Reference Information

Image 48

Contents DDS Digital Display ScalerSafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolRear panel video outputs QS-1Default display cycle Quick Start DDS 402, cont’dMain menu Input menu QS-2Memory Presets menu Output menuQS-3 Advanced Configuration menu Picture Adjustments menuExecutive Mode menu Exit menuTable of Contents Table of Contents, cont’d Digital Display Scaler Table of Contents Iii Iv Digital Display Scaler Table of Contents One Introductiontroduction, cont’d About this ManualAbout the Scaler Digital Display Scaler IntroductionFeatures Introduction, cont’d Digital Display Scaler Introduction Introduction, cont’d Two Installationstallation, cont’d Installation OverviewMounting the Scaler Cabling and Rear Panel ViewsVideo input connections Video output connectionsInstallation, cont’d ConfigurationPower connection RS-232 connectionThree Front Panel Controls and Indicators Operationeration, cont’dFreeze button Input buttonsPicture adjustment buttons Adjustment knobsLCD display Menu control buttonsPower Operation, cont’dFront Panel Operations Button iconsConfiguration Input Configuration menuPixel Phase submenu Output Configuration menuInput #2 submenu Resolution and refresh rates submenu Resolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 HzOutput Signal submenu Sync Polarity submenuSave Presets submenu Erase Presets submenuBlue Mode submenu RGB Delay submenuEdge Smoothing submenu Test Pattern submenuPicture adjustments Reset submenuFront panel security lockout executive mode Adjust knobs have no mechanical limits to their rotationSetting up a DVD source Optimizing the VideoFour Symbols Digital Display Scaler Programmer’s GuideScaler-Initiated Messages RGB delay PresetsProgrammer’s Guide, cont’d Test patternScaler Error Responses Using the Command/Response TableHost-to-Scaler Instructions Command/response table for SIS commands Command Ascii Command Response Additional descriptionCommand/response table for SIS commands cont’d Test pattern Command/response table for special function SIS commands Command Ascii Command ResponseProgrammer’s Guide, cont’d Five Installing the software Using the control programControl Software for Windows Digital Display Scaler Scaler SoftwareUsing the help program Control program I/O configuration windowUsing the software Scaler Software, cont’dButton Label Generator AAppendix a Specifications Digital Display Scaler Reference InformationPart Numbers Included partsSuggested part Included parts Part numberFirmware Upgrade Installation Reference Information, cont’dU24 U60 U68U67 Installing labels in the scaler’s buttons Button LabelsFCC Class a Notice Extron’s Warranty Extron Electronics, USA

Related manuals

Manual 2 pages 53.37 Kb