Magnavox TB100MW9A Connections, Connecting to a TV without A/V Jacks, White Red Yellow

Page 10

Connections

1Disconnect the AC power cords of the devices from the AC outlet.

Desconecte los cables de alimentación de los aparatos del tomacorriente CA.

2Disconnect RF coaxial cable from antenna input jack of your TV.

Desconecte el cable coaxial de RF del conector hembra de entrada de antena de su televisor.

3Make the connections as illustrated below.

Efectúe las conexiones tal como se ilustra a continuación.

4Plug all AC power cords into AC outlets, then turn all devices on.

Enchufe todos los cables eléctricos de CA en los tomacorrientes de CA y conecte la alimentación de todos los equipos.

AConnecting to a TV without A/V Jacks

Conexión a un TV sin tomas de A/V

TV

TV antenna

Antena de TV

STB

				RF cable


	Does not send

				(supplied)
	the analog TV signal.
	the analog TV signal.			cable de RF
No envía la señal analógica				(se incluye)

BConnecting to a TV with A/V Jacks

Conexión a un TV con tomas de A/V

TV

TV antenna

Antena de TV

STB

white

red

yellow

NOTE:

	yel
whi low
red	te

Audio cable
cable de audio		Video cable
		Video cable
		cable de
		video

•If your TV has only one audio jack, connect the AUDIO OUT jack (L) (white) on the STB to the audio input jack on the TV.

Si su TV sólo tiene una toma de audio, conecte la toma AUDIO OUT (L) (blanco) del STB, a la toma de entrada de audio del TV.

10

EN

Image 10

Contents TB100MW9A Before Using Risk of Electric Shock Do not OpenInsert Precautions Important Copyright InformationBefore Using Advanced Operation B l e o f C o n t e n t sOverview Installing Batteries AccessoriesInformation on Digital Broadcasting Remote Control Location of ControlsFront Panel Rear PanelConnections Connecting to a TV without A/V JacksConnecting to a TV with A/V Jacks White Red YellowWhite Connecting to a Cable Box OptionalEllow Yellow White Connecting to Other DevicesWhite Switch the STB’s mains power on Initial Setup Setup WizardInitial Setup Press STANDBY-ON on the remote control to activate the STBSelect your time zone using K / L, then press OK Select Continue using s / B, then press OKSelect the language using K / L, then press OK Select Autoscan using K / L, then press OKEnter the main channel number Basic OperationSelecting Channels on the STB Enter the sub-channel numberPress Still To cancel still modePress Audio repeatedly Choosing Audio LanguagePress EPG while watching TV Select the desired program using s / BPress Display Channel BannerAdvanced Operation Press SetupSelect ADD/ Delete using K / L, then press OK Autoscan Receiving ChannelsPress OK again to add the channel to the channel map Press Setup to exitSelect Delete using K / L, then press OK AddPress Setup Select Detail using K / L, then press OK Adjusting AntennaSelecting Display Mode SelectDISPLAY MODEusing K / L, then press OKSelect your time zone using K / L , then press OK Press Setup Select Time using K / L , then press OKSelect Time Zone using K / L , then press OK Time ZoneEnter the password using the Number buttons Select D.S.T using K / L , then press OKSelect on or OFF using s / B , then press OK Chip OptionsThen press OK repeatedly to switch between view and block Select the desired rating type using K / L , then press OKSelect the desired rating using Mpaa RatingSelect NEW Password using K / L , then press OK Enter the new 4-digit password using the Number buttonsSelect Manual using K / L , then press OK Press Setup Select Detail using K / L , then press OKClosed Caption Options Select desired amount of time using K / L , then press OK Auto Power DownSpecifications Advanced Operation / OthersTroubleshooting OthersX6045UD Customer ServiceTel 1VMN25613