Magnavox TB100MW9A owner manual Insert

Page 3

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE ANTENNA LEAD IN WIRE

 

GROUND CLAMP

ANTENNA

 

DISCHARGE UNIT

 

 

 

 

(NEC SECTION 810-20)

ELECTRIC SERVICE

 

 

EQUIPMENT

 

 

 

 

GROUNDING

NEC - NATIONAL

 

CONDUCTORS

ELECTRICAL CODE

 

(NEC SECTION 810-21)

POWER SERVICE GROUNDING ELECTRODE

GROUND CLAMPS

 

SYSTEM (NEC ART 250, PART H)

 

Before Using

conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)

14.Lightning - For added protection for this product receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to this product due to lightning and power-line surges.

15.Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16.Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on this product.

18.Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19.Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power-supply cord or plug is damaged or frayed.

b.If liquid has been spilled, or objects have fallen into this product.

c.If this product has been exposed to rain or water.

d.If this product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore this product to its normal operation.

e.If this product has been dropped or damaged in any way.

f.When this product exhibits a distinct change in performance-this indicates a need for service.

20.Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.

21.Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform routine safety checks to determine that this product is in proper operating condition.

22.Heat - This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

The serial number of this product may be found on the bottom of the unit. You should record the number and other vital information here and retain this book as a permanent record. Serial numbers are not kept on file.

Date of Purchase

 

 

Dealer Phone No.

 

Dealer Purchase from

 

Model No.

 

Dealer Address

 

 

Serial No.

 

 

 

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

 

INSERT.

 

 

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or climbing on it. A falling unit can cause serious injury or even death.

3

EN

Page 2 Page 4
Image 3
Page 2 Page 4
Contents TB100MW9A Risk of Electric Shock Do not Open Before UsingInsert Important Copyright Information PrecautionsB l e o f C o n t e n t s Before Using Advanced OperationOverview Accessories Installing BatteriesInformation on Digital Broadcasting Location of Controls Remote ControlRear Panel Front PanelWhite Red Yellow Connecting to a TV without A/V JacksConnecting to a TV with A/V Jacks ConnectionsConnecting to a Cable Box Optional WhiteEllow Connecting to Other Devices Yellow WhiteWhite Press STANDBY-ON on the remote control to activate the STB Initial Setup Setup WizardInitial Setup Switch the STB’s mains power onSelect Autoscan using K / L, then press OK Select Continue using s / B, then press OKSelect the language using K / L, then press OK Select your time zone using K / L, then press OKEnter the sub-channel number Basic OperationSelecting Channels on the STB Enter the main channel numberChoosing Audio Language To cancel still modePress Audio repeatedly Press StillChannel Banner Select the desired program using s / BPress Display Press EPG while watching TVAutoscan Receiving Channels Press SetupSelect ADD/ Delete using K / L, then press OK Advanced OperationAdd Press Setup to exitSelect Delete using K / L, then press OK Press OK again to add the channel to the channel mapSelectDISPLAY MODEusing K / L, then press OK Adjusting AntennaSelecting Display Mode Press Setup Select Detail using K / L, then press OKTime Zone Press Setup Select Time using K / L , then press OKSelect Time Zone using K / L , then press OK Select your time zone using K / L , then press OKChip Options Select D.S.T using K / L , then press OKSelect on or OFF using s / B , then press OK Enter the password using the Number buttonsMpaa Rating Select the desired rating type using K / L , then press OKSelect the desired rating using Then press OK repeatedly to switch between view and blockEnter the new 4-digit password using the Number buttons Select NEW Password using K / L , then press OKPress Setup Select Detail using K / L , then press OK Select Manual using K / L , then press OKClosed Caption Options Advanced Operation / Others Auto Power DownSpecifications Select desired amount of time using K / L , then press OKOthers Troubleshooting1VMN25613 Customer ServiceTel X6045UD
Top Page Image Contents