Magnavox TB100MW9A Advanced Operation, Autoscan Receiving Channels, Adding/Deleting Channels

Page 18

Advanced Operation

Autoscan

(Receiving Channels)

Autoscan receives available digital channels and stores them in a channel map.

CAUTION:

•If autoscan is skipped, digital channels may not be received correctly.

1 Press [SETUP].

2Select “CHANNEL” using [ K / L], then press [OK].

3Select “AUTOSCAN” using [ K / L], then press [OK].

CHANNEL

EXIT

ADD/DELETE

CHANNEL

ANTENNA

TIME

AUTOSCAN

DETAIL

INITIAL

4Select “AUTOSCAN” using [ K / L], then press [OK].

AUTOSCAN

To cancel during scanning:

Press [SETUP] or [OK].

NOTE:

•If canceled, some channels not yet scanned may not be received. We recommend completing autoscan.

•When you want to completely refresh the channel map, delete all the channels, then do the autoscan again. See “Adding/Deleting Channels” on this page for details.

When “NO SIGNAL” appears on the TV screen:

Verify the antenna connection, then scan again.

The STB tunes in channel 2-1 and “NO SIGNAL” appears if the STB could not receive any channels.

Adding/Deleting Channels

Add or delete desired channels in the channel map.

CAUTION:

•You cannot recover the deleted channels once they are deleted unless you perform the autoscan again.

1 Press [SETUP].

EXIT

CHANNEL

AUTOSCAN will rescan all channels. This may take a while to complete.

2Select “CHANNEL” using [ K / L], then press [OK].

TIME		BACK
DETAIL		AUTOSCAN
INITIAL
INITIAL

SETUP

AUTOSCAN

The system is now scanning.

EXIT

CHANNEL

TIME

DETAIL INITIAL

ADD/DELETE

ANTENNA

AUTOSCAN



12%			Channel Found

	EXIT

3Select “ADD/ DELETE” using [ K / L], then press [OK].

CHANNEL

•STB starts receiving available digital channels and stores them in the channel map.

•When the scanning is complete, “AUTOSCAN COMPLETED” will be indicated.

•After autoscan is complete, use [CH K / L] to verify whether STB is receiving channels properly.

EXIT

CHANNEL

TIME

DETAIL

INITIAL

18

ADD/DELETE

ANTENNA

AUTOSCAN

EN

Image 18

Contents TB100MW9A Before Using Risk of Electric Shock Do not OpenInsert Precautions Important Copyright InformationBefore Using Advanced Operation B l e o f C o n t e n t sOverview Accessories Installing BatteriesInformation on Digital Broadcasting Remote Control Location of ControlsFront Panel Rear PanelConnections Connecting to a TV without A/V JacksConnecting to a TV with A/V Jacks White Red YellowConnecting to a Cable Box Optional WhiteEllow Connecting to Other Devices Yellow WhiteWhite Switch the STB’s mains power on Initial Setup Setup WizardInitial Setup Press STANDBY-ON on the remote control to activate the STBSelect your time zone using K / L, then press OK Select Continue using s / B, then press OKSelect the language using K / L, then press OK Select Autoscan using K / L, then press OKEnter the main channel number Basic OperationSelecting Channels on the STB Enter the sub-channel numberPress Still To cancel still modePress Audio repeatedly Choosing Audio LanguagePress EPG while watching TV Select the desired program using s / BPress Display Channel BannerAdvanced Operation Press SetupSelect ADD/ Delete using K / L, then press OK Autoscan Receiving ChannelsPress OK again to add the channel to the channel map Press Setup to exitSelect Delete using K / L, then press OK AddPress Setup Select Detail using K / L, then press OK Adjusting AntennaSelecting Display Mode SelectDISPLAY MODEusing K / L, then press OKSelect your time zone using K / L , then press OK Press Setup Select Time using K / L , then press OKSelect Time Zone using K / L , then press OK Time ZoneEnter the password using the Number buttons Select D.S.T using K / L , then press OKSelect on or OFF using s / B , then press OK Chip OptionsThen press OK repeatedly to switch between view and block Select the desired rating type using K / L , then press OKSelect the desired rating using Mpaa RatingSelect NEW Password using K / L , then press OK Enter the new 4-digit password using the Number buttonsPress Setup Select Detail using K / L , then press OK Select Manual using K / L , then press OKClosed Caption Options Select desired amount of time using K / L , then press OK Auto Power DownSpecifications Advanced Operation / OthersTroubleshooting OthersX6045UD Customer ServiceTel 1VMN25613