Magnavox TB100MW9A Information on Digital Broadcasting, Accessories, Installing Batteries

Page 7

Information on Digital Broadcasting

Before Using

Receives	ATSC
ATSC

Digital

Digital terrestrialterrestrial signals antenna

STB (Set Top Box)

converts the ATSC signal to analog signal

TV

This STB makes it possible to view the digital TV programs on your analog TV by converting the digital signal to the analog signal. You can use most features provided by the digital broadcast, except that the resolution of the image is always output in 480i (standard resolution).

Accessories

Check the following accessories when unpacking the STB:

Remote control:	Owner’s manual:	AA battery (x2)	RF cable:
NA386UD (x1)	1VMN25613 (x1)		WPZ0901TM002 /
			WPZ0901TM005 (x1)

Installing Batteries

Instalación de pilas

1 Unsnap the battery cover from the	2 Install two AA batteries making	3 Snap the battery
back of the remote control.	sure the polarity (+ / - ) is correct.	cover back.
Abra la cubierta de pilas de la parte	Instale dos pilas AA asegurándose que	Cierre la cubierta de
trasera del mando a distancia.	la polaridad (+ / - ) sea la correcta.	pilas.

NOTE:

•When replacing batteries, replace them in pairs.

Cuando cambie las pilas, hágalo por pares.

CAUTION:

•Do not mix battery types (alkaline and manganese, or old ones and new ones).

No mezcle tipos de baterías (baterías alcalinas y de manganeso, ni pilas viejas con pilas nuevas).

•Do not recharge, short-circuit, heat, burn or disassemble batteries.

No recargue, caliente, queme o desarme baterías ni provoque un corto circuito con ellas.

•Remove batteries from battery compartment that is not going to be used for a month or more.

Quite las pilas del compartimento de pilas si no se va a utilizar durante un mes o más.

7

EN

Image 7

Contents TB100MW9A Risk of Electric Shock Do not Open Before UsingInsert Important Copyright Information PrecautionsB l e o f C o n t e n t s Before Using Advanced OperationOverview Installing Batteries AccessoriesInformation on Digital Broadcasting Location of Controls Remote ControlRear Panel Front PanelWhite Red Yellow Connecting to a TV without A/V JacksConnecting to a TV with A/V Jacks ConnectionsWhite Connecting to a Cable Box OptionalEllow Yellow White Connecting to Other DevicesWhite Press STANDBY-ON on the remote control to activate the STB Initial Setup Setup WizardInitial Setup Switch the STB’s mains power onSelect Autoscan using K / L, then press OK Select Continue using s / B, then press OKSelect the language using K / L, then press OK Select your time zone using K / L, then press OKEnter the sub-channel number Basic OperationSelecting Channels on the STB Enter the main channel numberChoosing Audio Language To cancel still modePress Audio repeatedly Press StillChannel Banner Select the desired program using s / BPress Display Press EPG while watching TVAutoscan Receiving Channels Press SetupSelect ADD/ Delete using K / L, then press OK Advanced OperationAdd Press Setup to exitSelect Delete using K / L, then press OK Press OK again to add the channel to the channel mapSelectDISPLAY MODEusing K / L, then press OK Adjusting AntennaSelecting Display Mode Press Setup Select Detail using K / L, then press OKTime Zone Press Setup Select Time using K / L , then press OKSelect Time Zone using K / L , then press OK Select your time zone using K / L , then press OKChip Options Select D.S.T using K / L , then press OKSelect on or OFF using s / B , then press OK Enter the password using the Number buttonsMpaa Rating Select the desired rating type using K / L , then press OKSelect the desired rating using Then press OK repeatedly to switch between view and blockEnter the new 4-digit password using the Number buttons Select NEW Password using K / L , then press OKSelect Manual using K / L , then press OK Press Setup Select Detail using K / L , then press OKClosed Caption Options Advanced Operation / Others Auto Power DownSpecifications Select desired amount of time using K / L , then press OKOthers Troubleshooting1VMN25613 Customer ServiceTel X6045UD