Magnavox TB100MW9A owner manual Initial Setup Setup Wizard, Switch the STB’s mains power on

Page 13

Initial Setup (Setup Wizard)

Initial Setup

Ajùste inicial

1 Switch the STB’s mains power on.

Encienda la alimentación principal del STB.

ON OFF

lights up in yellow

se vuelve amarilla

2 Press [STANDBY-ON] on the remote control to activate the STB.

Presione [STANDBY-ON] en el mando a distancia para activar el STB.

lights up in green

se vuelve verde

3Turn on the TV, and select the viewing channel (ch3 or external input channel) on your TV. (Refer to your TV’s manual.)

Encienda el TV, y seleccione el canal que quiera ver (canal 3 o uno de entrada externo) en su TV. (Véase el manual del TV.)

2

1

Appropriate Viewing Channel

Configuración apropiada de el Canal de Visión

	Viewing	STB	Cable Box	DVD or VCR
	Connection

	A (p.10)	“CH3”	-	-
	B (p.10)	External input channel	-	-
		Canal de entrada externo

	C (p.11)	External input channel	Ch3	-
		Canal de entrada externo

	D (p.12)	“CH3”	-	External input channel
				Canal de entrada externo

•If your TV’s ch3 is already occupied, select ch4, and set the STB’s output channel to ch4. You can switch ch3 / ch4 by holding [SETUP] down over 3 seconds.

Si el c3 de su TV ya está ocupado, seleccione el c4 y luego ajuste el canal de salida del STB a c4. Puede alternar entre el c3 y 4 manteniendo presionado [SETUP] durante 3 segundos.

”SETUP WIZARD” screen automatically appears.

Follow the directions shown on the TV screen to set the each setting.

13

Initial Setup (Setup Wizard)

EN

Image 13

Contents TB100MW9A Risk of Electric Shock Do not Open Before UsingInsert Important Copyright Information PrecautionsB l e o f C o n t e n t s Before Using Advanced OperationOverview Installing Batteries AccessoriesInformation on Digital Broadcasting Location of Controls Remote ControlRear Panel Front PanelConnecting to a TV with A/V Jacks Connecting to a TV without A/V JacksConnections White Red YellowWhite Connecting to a Cable Box OptionalEllow Yellow White Connecting to Other DevicesWhite Initial Setup Initial Setup Setup WizardSwitch the STB’s mains power on Press STANDBY-ON on the remote control to activate the STBSelect the language using K / L, then press OK Select Continue using s / B, then press OKSelect your time zone using K / L, then press OK Select Autoscan using K / L, then press OKSelecting Channels on the STB Basic OperationEnter the main channel number Enter the sub-channel numberPress Audio repeatedly To cancel still modePress Still Choosing Audio LanguagePress Display Select the desired program using s / BPress EPG while watching TV Channel BannerSelect ADD/ Delete using K / L, then press OK Press SetupAdvanced Operation Autoscan Receiving ChannelsSelect Delete using K / L, then press OK Press Setup to exitPress OK again to add the channel to the channel map AddSelecting Display Mode Adjusting AntennaPress Setup Select Detail using K / L, then press OK SelectDISPLAY MODEusing K / L, then press OKSelect Time Zone using K / L , then press OK Press Setup Select Time using K / L , then press OKSelect your time zone using K / L , then press OK Time ZoneSelect on or OFF using s / B , then press OK Select D.S.T using K / L , then press OKEnter the password using the Number buttons Chip OptionsSelect the desired rating using Select the desired rating type using K / L , then press OKThen press OK repeatedly to switch between view and block Mpaa RatingEnter the new 4-digit password using the Number buttons Select NEW Password using K / L , then press OKSelect Manual using K / L , then press OK Press Setup Select Detail using K / L , then press OKClosed Caption Options Specifications Auto Power DownSelect desired amount of time using K / L , then press OK Advanced Operation / OthersOthers TroubleshootingTel Customer ServiceX6045UD 1VMN25613