Fostex D-108 owner manual Scsi ID number setting

Page 11

Be sure to install the SCSI terminator.

D-108 Quick Operation Guide

	ANALOG IN				ANALOG OUT			MIDI		DATA	SCSI
4	3	2	1	4	3	2	1				AC IN
4	3	2	1	4	3	2	1
							INPUT	OUTPUT	THRU	INPUT	OUTPUT
8	7	6	5	8	7	6	5

Connect the SCSI cable securely.

<Notes on connection>

•Before making connections, make sure that both the D-108 and the SCSI drive are turned off.

•Up to two SCSI drives may be connected on a SCSI chain with the D-108.

Connect one SCSI drive as a “current drive” for real-time recording/playback. (Refer to “SCSI ID number setting” below.)

Refer to the main Owner’s Manual for more information on connecting a SCSI drive as a back-up drive.

	back-up drive (ID=6)			current drive (SCSI ID=any
	back-up drive (ID=6)			number other than “6”)
				number other than “6”)

	DATA	SCSI
		AC IN
THRU	INPUT	OUTPUT

•The SCSI connector on the D-108 is a 25-pin connector compatible with Macintosh computers. Use a cable with connectors that conform to the standards for connecting a SCSI drive.

•The last SCSI drive on the SCSI chain should be terminated. Install a SCSI terminator, or turn the termination switch to “on” if the drive has a termination switch (like a Zip drive).

<SCSI ID number setting>

•Be sure to set the SCSI ID number for the SCSI drive correctly, according to the purpose of the drive (as a current drive or a back-up drive). The ID setting is very important.

Using the SCSI drive as a current drive	Select any number from 0 to 5, but not “6.”

Using the SCSI drive as a back-up drive	Select “6.”

11

Image 11

Contents Welcome to D-108 ModelQuick Operation Guide Table of Contents Recording media Package contentsDisassembling the removable case Using an E-IDE hard diskInstalling a hard disk in a removable case Fixing the hard disk to the case Connecting cablesAssembling the case Installing the removable case in the D-108Connecting a detachable controller Press the EXECUTE/YES key Connect the D-108’s power cable to the AC outletTurn on the power to the D-108 Formatting a diskProgram Press the EXIT/NO key or the Stop buttonConnecting a Scsi drive to the D-108 Using a Scsi driveInstalling a detachable controller to the D-108 Scsi ID number setting Insert an unformatted disk in the Scsi drive Turn on the power to the D-108 and the Scsi driveFormatting a Scsi disk Record mode Use the JOG dial to select the desired Record modeEjecting the removable disk from the Scsi drive Press the Disp SEL key twice to enter Setup mode Using two current drivesPress the EXECUTE/YES key again Selecting a current driveConnecting a mixer Patchbay Buss OUT Group OUT 1~4 Tape in 1~8 Basic recording Initial settingsSetting sampling frequency Turn the JOG dial to select the desired sampling frequency Press the EXIT/NO key or the Stop button to quit Setup modeBasic analog recording Undo and redo recording To cancel the undo operation, press the Redo key againLocate the top of the Program Multitrack recording using overdubbingPing-pong recording Press the Record button oncePress the EXECUTE/YES key MixdownRecording in a new Program Turn the JOG dial clockwise to select New Program?Turn the JOG dial clockwise or counter-clockwise Basic Locate functionSelecting the desired Program from multiple Programs Locating the end of the recorded area of the ProgramTo turn off Vari Pitch mode, press the Vari Pitch key Playback using the Vari-pitch functionSet the desired pitch data using the JOG dial Press the Recall key, then press the Vari Pitch keyReference Fostex Corporation