Fostex D-108 Basic Locate function, Selecting the desired Program from multiple Programs

Page 25

D-108 Quick Operation Guide

<Selecting the desired Program from multiple Programs>

If you have set up multiple Programs on the disk, you first need to select the target Program prior to recording, playback, or edit. To select a Program, follow the steps below. Do not select a different Program until you finish the session.

1.While the D-108 is stopped, hold down the HOLD/> key and press the STORE key.

[Select PGM!] appears momentarily, then the number and title of the current Program appear.

2.Turn the JOG dial clockwise or counter-clockwise.

The numbers and titles of the Programs on the disk appear in turn.

3.Select the desired Program number and press the EXECUTE/YES key.

The top of the selected Program appears in ABS Time Base (ABS 0).

Basic Locate function

The Locate function enables you to locate the desired point (move the current position of the recorder) immediately. There are two locate methods: storing the desired locate point (time or bar/beat/clock value) into the memory keys, and locating the point without storing it.

This section explains “Locating the top of the Program” and “Locating the last recording point in the Program” and do not involve storing locate points. Refer to the User’s Guide for information on storing and locating locate points.

On the D-108, the top of the Program on the disk is called “ABS 0” and the end of the recorded area is called “REC END.” (If the Program has no data recorded, ABS 0 corresponds to REC END.) You can use this function to locate the ABS 0 or REC END point immediately, regardless of the current recorder position.

ABS 0

REC END

Recorded area

Locating ABS 0

Locating REC END

Current position

Locating the top of the Program

You can immediately move to the top of the Program (ABS 0), regardless of the current position of the Program.

1.Press and hold down the STOP button, and press the REWIND button.

1

 

ENVELOPE

 

 

 

RECORD

STOP

PLAY

REWIND

F FWD

CLIPBOARD PLAY

LOCATE ABS 0

LOCATE REC END

Locating the end of the recorded area of the Program

You can immediately move to the end of the recorded area of the Program, regardless of the current position of the Program.

1.Hold down the STOP button and press the F FWD

button.1

 

ENVELOPE

 

 

 

RECORD

STOP

PLAY

REWIND

F FWD

CLIPBOARD PLAY

LOCATE ABS 0

LOCATE REC END

25

Image 25
Contents Welcome to D-108 ModelQuick Operation Guide Table of Contents Recording media Package contentsInstalling a hard disk in a removable case Using an E-IDE hard diskDisassembling the removable case Fixing the hard disk to the case Connecting cablesConnecting a detachable controller Installing the removable case in the D-108Assembling the case Turn on the power to the D-108 Connect the D-108’s power cable to the AC outletFormatting a disk Press the EXECUTE/YES keyProgram Press the EXIT/NO key or the Stop buttonInstalling a detachable controller to the D-108 Using a Scsi driveConnecting a Scsi drive to the D-108 Scsi ID number setting Formatting a Scsi disk Turn on the power to the D-108 and the Scsi driveInsert an unformatted disk in the Scsi drive Record mode Use the JOG dial to select the desired Record modeEjecting the removable disk from the Scsi drive Press the Disp SEL key twice to enter Setup mode Using two current drivesPress the EXECUTE/YES key again Selecting a current driveConnecting a mixer Patchbay Buss OUT Group OUT 1~4 Tape in 1~8 Setting sampling frequency Initial settingsBasic recording Turn the JOG dial to select the desired sampling frequency Press the EXIT/NO key or the Stop button to quit Setup modeBasic analog recording Undo and redo recording To cancel the undo operation, press the Redo key againPing-pong recording Multitrack recording using overdubbingPress the Record button once Locate the top of the ProgramRecording in a new Program MixdownTurn the JOG dial clockwise to select New Program? Press the EXECUTE/YES keySelecting the desired Program from multiple Programs Basic Locate functionLocating the end of the recorded area of the Program Turn the JOG dial clockwise or counter-clockwiseSet the desired pitch data using the JOG dial Playback using the Vari-pitch functionPress the Recall key, then press the Vari Pitch key To turn off Vari Pitch mode, press the Vari Pitch keyReference Fostex Corporation