Fostex D-108 owner manual Use the JOG dial to select the desired Record mode

Page 13

D-108 Quick Operation Guide

Use the JOG dial to select the desired Record mode.

You may select [8track format] or [4track format]. [8track format] is a common selection.

If you also wish to use the disk on a four-track multitracker, FD-4, for recording and playback, select [4track format].

 

SETUP

 

SETUP

OL

FORMAT

OL

FORMAT

0

 

0

 

3

 

3

 

6

44.1kHz

6

 

9

9

44.1kHz

12

 

12

 

18

 

18

 

24

 

24

 

30

SURE?

30

SURE?

42

 

42

 

 

 

1 2 3 4 5 6 7 81 2 3 4 5 6 7 8

Record mode

8-track format

4-track format

 

Quantization

16 bit linear

16 bit linear

Sampling frequency

44.1kHz/48kHz

44.1kHz/48kHz

 

Available recording time

About 17min/100MB (converted one track)

About 17min/100MB (converted one track)

Compatible media

E-IDE hard disk

SCSI removable disk

(MO disk, Zip disk)

SCSI fixed disk

 

 

SCSI fixed disk

 

 

 

 

 

Recording track

8 tracks

4 tracks

 

* 8-track simultaneous recording of adat

* 4-track simultaneous recording of S/P DIF

 

digital signals (two inputs) and analog

 

digital inputs or eight analog inputs

 

signals (two inputs)

Recording capability

 

* 8-track simultaneous recording of S/P DIF

* 4-track simultaneous recording of four

 

 

analog inputs

 

digital signals (two inputs) and analog

 

* 4-track simultaneous recording of adat

 

signals (six inputs)

 

digital inputs (from adat outputs 1-4)

 

 

 

 

 

Save/load

Save and load using a back-up SCSI drive,

Save and load using a back-up SCSI drive,

DAT, or adat

DAT, or adat

 

 

 

 

 

<Note>

Actual available recording time obtained by disk formatting may vary depending on the disk type.

Press and hold down the [RECORD] button and press the EXECUTE/YES key.

When the D-108 starts formatting, it displays the size of the unformatted area on the disk, and counts down as formatting proceeds. Also, the segments in the “∞” column of the level meters light up, and turn off one by one starting at right, indicating the status of the format operation. It will take a while to complete formatting, especially if you are formatting a large-capacity disk.

OL

0

3

6

9

12

18

24

30

42

1

2

3

4

5

6

7

8

SETUP

REMAIN

FORMAT

44.1kHz

The [#] mark indicates the SCSI ID number and the [*****] mark indicates the size of unformatted area on the hard disk (e.g., 350MB).

When the format operation is completed, the screen changes as follows and the disk operation stops.

OL

0

3

6

9

12

18

24

30

42

SETUP

FORMAT

44.1kHz

COMPLETED!

[COMPLETED!] appears and the disk stops.

1

2

3

4

5

6

7

8

13

Image 13
Contents Welcome to D-108 ModelQuick Operation Guide Table of Contents Recording media Package contentsInstalling a hard disk in a removable case Using an E-IDE hard diskDisassembling the removable case Fixing the hard disk to the case Connecting cablesConnecting a detachable controller Installing the removable case in the D-108Assembling the case Turn on the power to the D-108 Connect the D-108’s power cable to the AC outletFormatting a disk Press the EXECUTE/YES keyProgram Press the EXIT/NO key or the Stop buttonInstalling a detachable controller to the D-108 Using a Scsi driveConnecting a Scsi drive to the D-108 Scsi ID number setting Formatting a Scsi disk Turn on the power to the D-108 and the Scsi driveInsert an unformatted disk in the Scsi drive Record mode Use the JOG dial to select the desired Record modeEjecting the removable disk from the Scsi drive Press the Disp SEL key twice to enter Setup mode Using two current drivesPress the EXECUTE/YES key again Selecting a current driveConnecting a mixer Patchbay Buss OUT Group OUT 1~4 Tape in 1~8 Setting sampling frequency Initial settingsBasic recording Turn the JOG dial to select the desired sampling frequency Press the EXIT/NO key or the Stop button to quit Setup modeBasic analog recording Undo and redo recording To cancel the undo operation, press the Redo key againPing-pong recording Multitrack recording using overdubbingPress the Record button once Locate the top of the ProgramRecording in a new Program MixdownTurn the JOG dial clockwise to select New Program? Press the EXECUTE/YES keySelecting the desired Program from multiple Programs Basic Locate functionLocating the end of the recorded area of the Program Turn the JOG dial clockwise or counter-clockwiseSet the desired pitch data using the JOG dial Playback using the Vari-pitch functionPress the Recall key, then press the Vari Pitch key To turn off Vari Pitch mode, press the Vari Pitch keyReference Fostex Corporation