Gefen EXT-HDMI-CAT5-844 user manual Edid Management Options, Edid Modes, Function

Page 15

EDID MANAGEMENT OPTIONS

v. 3019

 

EDID Modes

The diagram below illustrates the 8 DIP switch bank.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DIP SWITCH

Function

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

EDID Mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

EDID Mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

IR Channel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

IR Channel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

EDID Mode

1

 

2

3

 

4

5

 

6

7

 

8

 

6

N/A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

EDID Mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

N/A

Use DIP switches 1, 2, 5, and 7 to select the desired EDID management mode.

EDID Mode 0 (Switch 1=OFF Switch2=OFF Switch5=ON)

EDID is copied from the device connected to the first active hdmi output port.

All features newer that HDMI 1.2 are cleared.

EDID Mode 1 (Switch 1=ON Switch2=OFF Switch5=ON)

Same as Mode 0 and adds basic audio support.

EDID Mode 2 (Switch 1=OFF Switch2=ON Switch5=ON)

Same as Mode 0 and adds full audio support.

EDID Mode 3 (Switch 1=ON Switch2=ON Switch5=OFF)

EDID is generated based on the common video and audio features of all of the connected output devices.

EDID Mode 4 (Switch 1=OFF Switch2=ON Switch5=OFF)

Same as Mode 3 and adds basic audio support.

EDID Mode 5 (Switch 1=ON Switch2=OFF Switch5=OFF)

Same as Mode 3 and adds full audio support.

EDID Mode 6 (Switch 1=OFF Switch2=OFF Switch5=OFF) DEFAULT

EDID is generated based on the common video features of all of the connected devices and the combined audio features of all of the connected output devices.

EDID Mode 7 (Switch 1=ON Switch2=ON Switch5=ON)

EDID is passed unmodified from the device connected to the first active output port.

EDID Mode 8 (Switch 1=OFF Switch2=OFF Switch5=OFF Switch7=ON)

Preloaded generic 1080p EDID is used.

EDID Mode 9 (Switch 1=OFF Switch2=ON Switch5=OFF Switch7=ON)

Same as mode 6 but will record and store the EDID in memory. This EDID will persist no matter what displays are disconnected or reconnected thereafter. EDID will remain even upon power cycle. A user submitted EDID can be uploaded in this mode using a Gefen HDMI Signal Generator.

12

Image 15
Contents 8x4 CAT-5 Matrix for Write To Asking for AssistanceTechnical Support Technical Support HoursContents How It Works IntroductionGefen Gefen 8x4 CAT-5 Matrix for HdmiOperation Notes Package Includes FeaturesFront Panel Back Panel Sender Panel LayoutSender Panel Descriptions 13 24V DC Power Input Connecting and Operating the 8X4 CAT-5 Matrix for Hdmi How to Connect the 8x4 CAT-5 Matrix for HdmiHow to Operate the 8x4 CAT-5 Matrix for Hdmi Connecting the 8X4 CAT-5 Matrix for Hdmi Jumpers LED Indicator Input Selection Buttons RMT-16IR* Remote Control DescriptionHow Do I change the Remote Channel? RMT-16IR Remote Channel ConfigurationWhy would I need to change the remote channel? Am experiencing the issues listed above. What do I do?EDID. What is it and what is it used for? Edid Management FeatureEdid Management Options Edid ModesFunction LED Array Description Scenario 1 a ExampleHow do I use these features? What are the communication port settings?8X4 CAT-5 Matrix for Hdmi RS-232 Serial Communication Print Matrix Routing State 8X4 CAT-5 Matrix for Hdmi RS-232 CommandsSwitching/Routing Binary Table Edid Management ModesFront Panel Back Panel Top Panel Receiver Panel LayoutReceiver Panel Descriptions IR Blaster Functionality Operating the Hdmi Over CAT-5 ReceiverRMT-4IR Remote Control Description Auto Equalization & Boost Setting Hdmi Over CAT-5 Receiver Advanced ConfigurationIR Remote Channel Configuration Equalization SettingCurrent source is 1A Scenario 2 B ExampleHdmi Over CAT-5 Receiver RS-232 Serial Communications Boost Settings Hdmi Over CAT-5 Receiver RS-232 CommandsSpecifications