Fujitsu plasmavision user manual Minimizing phosphor burn-in Screen Orbiter For RGB

Page 47

• Minimizing phosphor burn-in (Screen Orbiter)

for RGB

You can use this option to move the screen position to minimize phosphor-induced “burn-in”.

Follow the steps below.

(1)Select “Screen Orbiter” and press <.

The “Screen Orbiter” setting screen will appear.

(2)Press Cor Dto select “Mode/Time”.

(3)Select a desired pattern.

Each time you press Eor F, one of the available choices appears in the following sequence:

“Screen Orbiter” setting screen

[Off]: Disables Screen Orbiter.

[Time]: Moves the pattern approximately every one hour.

[Mode]: Moves the pattern when the power is turned ON or when you switch between modes.

(4)Press Cor Dto select “Moving Area”.

(5)Press Eor Fto select the range for moving the pattern.

Each time you press Eor F, one of the available choices appears in the following sequence:

[Min.]: Pattern moves in small range. (About 5 pixels)

[Std.]: Pattern moves in moderate range. (About 10 pixels)

[Max.]: Pattern moves in wide range. (About 15 pixels)

(6)Press <to store.

*When the Screen Orbiter function is operated, some letters at the top, bottom, right or left of the screen may be missed.

• Setting RGB Input Signal Compulsorily (Direct Setting)

for RGB

You can use this option to switch the setting for RGB input signal.

Each time you press Eor F, one of the available choices appears in the following sequence:

[Auto]: The optimum display is obtained automatically for input signals.

[Others]: The optimum resolution setting is fixed for each signal. Press <to store.

*In Auto mode, the resolution of VGA, WVGA, 480P, XGA, WXGA, SXGA and SXGA+ may not be automatically distinguished. Switch to the fixed display when the image is not displayed properly.

*Signals that are not applicable depending on the model or input terminals may not be displayed.

• Specifying RGB Input Signal (Code Setting)

for mD-sub input

Normally, use this option in Auto mode.

Displaying white over entire screen (White Screen)

You can use this option to display white over the entire screen to minimize phosphor burn-in. Each time you press Eor F, one of the available choices appears in the following sequence:

On Off

Press <to store.

Note

The screen display disappears if there is no operation within approximately 60 seconds.

Depending on the model or the optional devices, some of the functions may not be available.

The adjustment range varies according to the display signals. Make adjustments to your preferred Sharpness within the adjustment range.

Depending on the type of signal, it may not be possible to make some of the settings or adjustments.

Póññêèé Português Italiano Français Español Deutsch English

中文

日 本 語

E-33

Image 47
Contents Póññêèé Português Italiano Français Español Deutsch English ContentsTwo big ferrite cores Checking AccessoriesConnecting the Display to External Equipment Ferrite coresReference InstallationDisplay Section Front Side Display Section Front Part Names and Functions RS-232C terminal RS-232C Back Bottom  / I power switchDisplay Section Back and Bottom Part  Hdmi input terminal VIDEO5 INPUT/HDMI for the U model External speaker output terminal EXT SP  Power input terminal Video input terminal VIDEO1 Input  S-Video input terminal VIDEO2 InputDescription of Input Terminals Pin No SignalPin No Input signal Hdmi High-Definition Multimedia Interface English OptionsVertical frequency Hz Signal Main Supported SignalsMain corresponding signals RGB mode Display dots x lines Frequency kHz Frequency Hz HdmiRegulation SpecificationModel P42VHA40U P42HHA40U P50XHA40U P55XHA40U P63XHA40U Specification Precautions and Adjustment Methods Information Using the Remote Control  CDEFAdjustment buttons Î E-19-E-35  &Video input mode selector button Î E-14 *RGB input mode selector button Î E-15  12Volume adjustment buttons Î E-13Precautions Putting Batteries in the Remote ControlUpper Lower Left Right Front Effective Range for the Remote ControlVCR or other external components See P. Î Example of Connection to External ComponentsDisplay bottom VCRItaliano DVD RECORDER/PLAYERÇais Español Deutsch Satellite Tuner Póññêèé Português Italiano Français Español Deutsch English Basic Operations Turning the Power on and STAND-BYPress on the remote control Press when the power is onMuting the audio Adjusting the VolumeAdjusting the volume Press &to select the input Mode Selecting Input ModePress =to select the input Mode Ñol Deutsch English RGB Input ModePress -*to select the input mode On-screen information Picture ModeOther Basic Operations Convenient FunctionsPress to select a desired Screen Size Switching Between Screen SizesWatching Pictures on the Wide Screen Press Aspect Ratio Screen SizeMenu Adjustment MenuPress Cor Dto select Tint Press to store Press when you finishPress Press Eor Fto select PictureAdjusting the Picture Setting Picture Memory Setting Picture ModePrecision Setting for the U model Setting Codec NR Adjusting the Black LevelSetting Detail Gradation Setting 3D NRChroma Transient Setting Image EnhanceAdjusting the Color Temp Setting User Color TempReddish color Setting the Color FocusÇais Español Deutsch English Jaggies Filter Making the Progressive Scan SettingsFrame Mode Motion SettingEspañol Deutsch English Adjusting Screen Position and SizeAdjusting Screen Position Position Adjusting Screen Size SizeAdjusting Volume Balance Balance Adjusting AudioAdjusting Treble Treble Adjusting Bass BassAdjustment Item Contents of Adjustments Operation Other AdjustmentsAdjustment Features setup screen has the following 4 optionsOn Screen Menu Ñol Setting the Input TerminalsSelecting the settings of Video/S-video Input terminal Selecting the settings of D-SUB Input terminalSelecting input terminals Audio Input Other SettingsAuto Off-NO SIG Displaying white over entire screen White Screen Specifying RGB Input Signal Code Setting For mD-sub inputMinimizing phosphor burn-in Screen Orbiter For RGB Displaying System Status Information Setting Exhibition Mode Exhibition ModeInput Signal Video mode Input Sync. Signal type Português Italiano Français Español Deutsch Initialization of User Adjustment ValuePress Eor Fto select Factory Press Cor Dto select the YesBefore Obtaining Service Cleaning and Maintenance