Vidikron 85 manual Remote Control, To install batteries in the remote control, Operation

Page 27

3Installation

3.1

Remote Control

To install batteries in the remote control:

Battery Installation

1.Remove the battery cover from the back of the remote control.

2.Insert the batteries included with the remote control. Ensure that the polarities correctly match the and markings inside the battery compartment.

3.Replace the battery cover.

1. Do not mix an old battery with a new one or different types of batteries.

Note

2. If you will not use the remote control for a long time, remove the batteries

to avoid damage from battery leakage.
The remote control can be used to control the Vision 85 within the ranges shown in Figure	Notes on Remote Control
3-1.	Operation

Component SD NTSC		480i
16:9

Approx.

7m/23ft

LIGHT

OFFON

						ENT
RETURN										MENU
EXIT
					MEMORY
			SOURCE SELECTION

Figure 3-1. Available Range of the Remote Control

Vidikron Vision 85 Owner’s Operating Manual

15

Image 27

Contents 1080p DLP Projectors Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Anamorphic Lens Installation and AdjustmentMaintenance and Troubleshooting SpecificationsSerial Communications Table of Contents 1List of Figures Typical Test Pattern for Adjusting Sharpness This Manual About This ManualIf you need Turn to Using This ManualThey also provide supplemental information Performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Vision 85 Front/Top/Side/Bottom/Rear View Vision 85 at a GlanceVertical Lens Shift Wired IR 3.5-mm, mini phono jack RS-232C Input RJ-11 female connectorVision 85 Rear Panel VHD Controller Front Panel VHD Controller Front PanelInputs Component Video RCA connectorsVHD Controller Rear Panel Hdmi 1 / Hdmi 2 DigitalComLink RS-232 Output Power Input 100 to 240 VACVideo 1 / S-VIDEO Volt 750 mA Trigger OutputsVHD Controller/Vision 85 Remote Control Vision 85 Remote Control Unit On / OFF ENT Enter Cursor Buttons VID 1 2 / S-VID 2 5 S-Video Memory Preset Buttons ISF NT NightCust VideoNot used Vision 85 Built-In KeypadRemote Control To install batteries in the remote controlOperation Installation If installing a Vision 85/CineWide or Vision 85/CineWide Quick SetupInstallation Overview Step Procedure For Details, Refer toProjector Calibration Digital 1080i or 1080p signals Installation ConsiderationsProjector Installation Options Installation TypeVision Throw Ratios for the Vision 85 SeriesThrow Range Throw Ratio Projector ModelCeiling Installation Floor InstallationPosition Folded Optics Installing the Optional CineWide Lens Mount 6shows the Vision 85/CineWide with AutoScope motor assembly Vision 85 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Vision 85/CineWide with Lens Base Plate 85/CineWideAngle Adjusting the ProjectionMounting the Vision Floor Mounting UprightConnector Panel Access Connections to the Vision 85 and VHD ControllerVHD Controller Hdmi Source HD-DVD/BD/DVD Player or HD Tuner with Connecting SourceHdmi Connections See Figure Controller12. Digital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See FigurePersonal Computer Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See Figure15. RS-232 Control System Connection Connecting a PC or Automation System to the VHD ControllerEquipment Outputs to External17 -volt Trigger Output Connection from Projector Connecting an External IR Receiver to the VHD ControllerPower source Turning on the PowerPrimary Lens Adjustments Adjusting the Picture OrientationAnamorphic Lens Installation Adjustment Vision 85/CineWide Installing and Adjusting the CineWide Anamorphic LensAdjusting the Lens Height Y Anamorphic Lens Top View Adjustment Vision 85/CineWide withAutoScope 22. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage PlateAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry 4Operation Using the On-Screen MenusAspect Ratio ISF PresetsService Input SourceMain Menu Input SourceAspect Ratio Aspect Ratio Description Aspect Ratio SettingsSurface, eliminating the black bars. PictureTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Typical Test Pattern for Adjusting SharpnessInformation ISF PresetsCalibration You must enter a passcode to access the Calibration menuGain/Offset Refer to ISF Night Display Color, above Service Code HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Standard VisionOperation On-Screen Menus for 1080i Digital or 1080p Signals Vidikron Video Auto Contrast Picture AdjustColor Temp VAC Iris Lamp Power KeyOperation Mpeg NR Picture Adjust AdvancedEffects of Primary Color Hue Adjustments White Balance White BalanceLamp Hours read-onlyRefer to Lamp Hours on OptionsAlways set this option to On. Doing otherwise may disrupt Orientation Refer to Adjusting the Picture Orientation onOperation Lamp Replacement 5Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution To Table Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands Value Description Min/max Stored? CommandBrightness Command Parameter Value Description Min/max Stored? Enter key Hdinputres YESSerial Communications Vision 85 Specifications Dimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsVHD Controller Specifications Vision 85/CineWide with AutoScope Dimensions Vision 85 DimensionsPage Vidikron