Vidikron 85 manual Gray Yellow Cyan Green Magenta Red Blue

Page 66

Operation

Select Color and press ENTER. While looking at the color bar pattern through a blue filter, adjust the color saturation level until the outermost (gray and blue) color bars appear to be a single shade of blue:

gray

yellow

cyan

green

magenta

red

blue

Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. When tint is decreased, the image appears redder; when it is increased the image appears greener. To set the tint, select Tint and press ENTER. While looking at the color bar pattern through a blue filter, adjust the tint level until the cyan and magenta color bars (on either side of the green bar) appear to be a single shade of blue.

Like the brightness and contrast controls, the color and tint controls are

Note interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting.

54	Vidikron Vision 85 Owner’s Operating Manual

Image 66

Contents 1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Anamorphic Lens Installation and Adjustment OperationMaintenance and Troubleshooting SpecificationsSerial Communications Table of Contents 1List of Figures Typical Test Pattern for Adjusting Sharpness About This Manual This ManualPerformance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories Vision 85 at a Glance Vision 85 Front/Top/Side/Bottom/Rear ViewVertical Lens Shift Wired IR 3.5-mm, mini phono jack RS-232C Input RJ-11 female connectorVision 85 Rear Panel VHD Controller Front Panel VHD Controller Front PanelHdmi 1 / Hdmi 2 Digital Component Video RCA connectorsVHD Controller Rear Panel InputsVolt 750 mA Trigger Outputs Power Input 100 to 240 VACVideo 1 / S-VIDEO ComLink RS-232 OutputVision 85 Remote Control Unit VHD Controller/Vision 85 Remote ControlOn / OFF ENT EnterCursor Buttons Video Memory Preset Buttons ISF NT NightCust VID 1 2 / S-VID 2 5 S-VideoVision 85 Built-In Keypad Not usedRemote Control To install batteries in the remote controlOperation Installation Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a Vision 85/CineWide or Vision 85/CineWideInstallation Type Installation ConsiderationsProjector Installation Options Projector Calibration Digital 1080i or 1080p signalsProjector Model Throw Ratios for the Vision 85 SeriesThrow Range Throw Ratio VisionCeiling Installation Floor InstallationPosition Folded Optics Installing the Optional CineWide Lens Mount 6shows the Vision 85/CineWide with AutoScope motor assembly Vision 85 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation 85/CineWide Vision 85/CineWide with Lens Base PlateFloor Mounting Upright Adjusting the ProjectionMounting the Vision AngleConnector Panel Access Connections to the Vision 85 and VHD ControllerVHD Controller Controller Connecting SourceHdmi Connections See Figure Hdmi Source HD-DVD/BD/DVD Player or HD Tuner withDigital DTV RGB or Component Video Connections See Figure 12. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnecting a PC or Automation System to the VHD Controller 15. RS-232 Control System ConnectionOutputs to External EquipmentConnecting an External IR Receiver to the VHD Controller 17 -volt Trigger Output Connection from ProjectorTurning on the Power Power sourceAdjusting the Picture Orientation Primary Lens AdjustmentsInstalling and Adjusting the CineWide Anamorphic Lens Anamorphic Lens Installation Adjustment Vision 85/CineWideAdjusting the Lens Height Y Anamorphic Lens Top View Adjustment Vision 85/CineWide withAutoScope Attach Lens Mounting Assembly to Lens Motor Carriage Plate 22. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Using the On-Screen Menus 4OperationInput Source ISF PresetsService Aspect RatioMain Menu Input SourceAspect Ratio Aspect Ratio Settings Aspect Ratio DescriptionPicture Surface, eliminating the black bars.Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input PositionISF Presets InformationYou must enter a passcode to access the Calibration menu CalibrationGain/Offset Refer to ISF Night Display Color, above Service Code Standard Vision HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVOperation On-Screen Menus for 1080i Digital or 1080p Signals Vidikron Video Key Picture AdjustColor Temp VAC Iris Lamp Power Auto ContrastOperation Picture Adjust Advanced Mpeg NREffects of Primary Color Hue Adjustments White Balance White BalanceOptions Lamp Hours read-onlyRefer to Lamp Hours onOrientation Refer to Adjusting the Picture Orientation on Always set this option to On. Doing otherwise may disruptOperation 5Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution To Table Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands Command Value Description Min/max Stored?Brightness Command Parameter Value Description Min/max Stored? Hdinputres YES Enter keySerial Communications Vision 85 Specifications Power Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsVHD Controller Specifications Vision 85 Dimensions Vision 85/CineWide with AutoScope DimensionsPage Vidikron