Vidikron 85 manual Installing and Adjusting the CineWide Anamorphic Lens

Page 50

Installation

3.10

Installing and Adjusting the CineWide Anamorphic Lens

Anamorphic Lens Installation ➤

and Adjustment - Vision

85/CineWide

If you are installing a CineWide-equipped projector, proceed as follows to install and adjust the anamorphic lens.

It is extremely important that the primary lens is properly adjusted

Note before you install the anamorphic lens. Ensure that the image from

the primary lens is perfectly centered on the screen.

The standard Vision 85/CineWide uses a prismatic-style anamorphic lens. This type of lens compresses the height of the image (as opposed to stretching the width) to achieve a 2.35:1 aspect ratio with a 1.78:1 display device.

The Vision 85/CineWide with AutoScope uses a cylindrical anamorphic lens with a much larger aperture than the prismatic lens used with the standard Vision 85/CineWide.

If you are installing a Vision 85/CineWide with AutoScope, refer to Anamorphic Lens Installation and Adjustment - Vision 85/CineWide with AutoScope on page 41. If you are installing a standard Vision 85/CineWide, continue with the next section.

The standard Vision 85 Anamorphic lens mount kit consists of everything shown in Figure

3-20.Some components shipped with your projector may differ slightly from what is shown in these instructions.

If any items are missing or damaged, please contact your Vidikron dealer or Vidikron Customer Service at (888) 4VIDIKRON.

1Anamorphic Lens

2 Base Plate

3Screw, Phillips

10-32 x 1/2" (4x) and Washer (4x)

(not shown; secures Base Plate to bottom of projector)

6Pitch/Y-Adjustment Screw, Phillips

Pan Head, 4-40 x 5/16" (4x) and Fender Washer (4x)

5Vertical Mounting

Bracket (2x)

4Yaw/Z-Adjustment Knob (2x) and Washer (2x)

Figure 3-20. Vision 85 Anamorphic Lens Mounting Assembly - Exploded View

1.Use the Pitch Adjustment Screws and Washers (item #6) to attach the Vertical Mounting Brackets (item #5) to the Anamorphic Lens (item #1).

2.Place the lens with the brackets installed on top of (or under, if the projector is inverted) the Base Plate (item #2), so that the two threaded posts at the bottom of the brackets pass through the corresponding slots on the base plate.

38	Vidikron Vision 85 Owner’s Operating Manual

Image 50

Contents 1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Anamorphic Lens Installation and Adjustment OperationSerial Communications Maintenance and TroubleshootingSpecifications Table of Contents 1List of Figures Typical Test Pattern for Adjusting Sharpness About This Manual This ManualPerformance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories Vision 85 at a Glance Vision 85 Front/Top/Side/Bottom/Rear ViewVertical Lens Shift Vision 85 Rear Panel Wired IR 3.5-mm, mini phono jackRS-232C Input RJ-11 female connector VHD Controller Front Panel VHD Controller Front PanelHdmi 1 / Hdmi 2 Digital Component Video RCA connectorsVHD Controller Rear Panel InputsVolt 750 mA Trigger Outputs Power Input 100 to 240 VACVideo 1 / S-VIDEO ComLink RS-232 OutputVision 85 Remote Control Unit VHD Controller/Vision 85 Remote ControlCursor Buttons On / OFFENT Enter Video Memory Preset Buttons ISF NT NightCust VID 1 2 / S-VID 2 5 S-VideoVision 85 Built-In Keypad Not usedOperation Remote ControlTo install batteries in the remote control Installation Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a Vision 85/CineWide or Vision 85/CineWideInstallation Type Installation ConsiderationsProjector Installation Options Projector Calibration Digital 1080i or 1080p signalsProjector Model Throw Ratios for the Vision 85 SeriesThrow Range Throw Ratio VisionPosition Ceiling InstallationFloor Installation Folded Optics Installing the Optional CineWide Lens Mount 6shows the Vision 85/CineWide with AutoScope motor assembly Vision 85 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation 85/CineWide Vision 85/CineWide with Lens Base PlateFloor Mounting Upright Adjusting the ProjectionMounting the Vision AngleVHD Controller Connector Panel AccessConnections to the Vision 85 and VHD Controller Controller Connecting SourceHdmi Connections See Figure Hdmi Source HD-DVD/BD/DVD Player or HD Tuner withDigital DTV RGB or Component Video Connections See Figure 12. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnecting a PC or Automation System to the VHD Controller 15. RS-232 Control System ConnectionOutputs to External EquipmentConnecting an External IR Receiver to the VHD Controller 17 -volt Trigger Output Connection from ProjectorTurning on the Power Power sourceAdjusting the Picture Orientation Primary Lens AdjustmentsInstalling and Adjusting the CineWide Anamorphic Lens Anamorphic Lens Installation Adjustment Vision 85/CineWideAdjusting the Lens Height Y Anamorphic Lens Top View AutoScope AdjustmentVision 85/CineWide with Attach Lens Mounting Assembly to Lens Motor Carriage Plate 22. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Using the On-Screen Menus 4OperationInput Source ISF PresetsService Aspect RatioAspect Ratio Main MenuInput Source Aspect Ratio Settings Aspect Ratio DescriptionPicture Surface, eliminating the black bars.Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input PositionISF Presets InformationYou must enter a passcode to access the Calibration menu CalibrationGain/Offset Refer to ISF Night Display Color, above Service Code Standard Vision HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVOperation On-Screen Menus for 1080i Digital or 1080p Signals Vidikron Video Key Picture AdjustColor Temp VAC Iris Lamp Power Auto ContrastOperation Picture Adjust Advanced Mpeg NREffects of Primary Color Hue Adjustments White Balance White BalanceOptions Lamp Hours read-onlyRefer to Lamp Hours onOrientation Refer to Adjusting the Picture Orientation on Always set this option to On. Doing otherwise may disruptOperation 5Maintenance and Troubleshooting Lamp ReplacementSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart To Table Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration Command Value Description Min/max Stored?Brightness Command Parameter Value Description Min/max Stored? Hdinputres YES Enter keySerial Communications Vision 85 Specifications Power Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsVHD Controller Specifications Vision 85 Dimensions Vision 85/CineWide with AutoScope DimensionsPage Vidikron