Sony STR-GA7ES, STR-GA8ES manual Using the Sleep Timer, 15EN, Recording on a video tape

Page 15

Recording on a video tape

You can record from a VCR, a TV, or a LD player using the receiver. You can also add audio from a variety of audio sources when editing a video tape. See your VCR or LD player’s instruction manual if you need help.

1Turn FUNCTION to select the program source to be recorded.

2Set the component to be ready for playing. For example, insert the laser disc you want to record from into the LD player.

3Insert a blank video tape into the recording VCR (VIDEO 1 or VIDEO 2).

4Start recording on the recording VCR and then start playing the video tape or laser disc you want to record.

Replacing audio while copying a video tape or laser disc

You can add audio from a variety of sources when editing a video tape. See your VCR or LD player’s instruction manual if you need help.

1Turn FUNCTION to select the video program source to be recorded.

2Press MODE repeatedly so that “AUDIO MODE” appears in the display.

The current video signal is fixed and you can select audio from any other source (except AC-3) whithout changing the current video signal.

3Use FUNCTION (or TAPE MONITOR) to select the audio you desire.

If you want to change the video program selected in step 1, press MODE to select “VISUAL MODE” and you can select video from another source while maintaining the current audio signal.

4Prepare the respective video and audio sources for playback.

5Insert a blank video tape into the recording VCR.

6Start recording on the recording VCR and then start playing both the video and audio sources you want to record.

Note

If you do not select the audio or video source within 8 seconds of pressing MODE, the “AUDIO MODE” or “VISUAL MODE” is cancelled and the audio or video source will not be fixed. In this case, press MODE again to display the mode you desire. The mode changes as follows:

VISUAL MODE /AUDIO MODE /off

Receiver Operations

To record other audio on a specific part of video

1Pause the video the point where you want to record the other audio.

2Press MODE to select “AUDIO MODE”, then use FUNCTION (or TAPE MONITOR) to select the audio source you desire.

3Start recording on the recording VCR, release the pause mode and start playing the audio source you want to record.

To resume recording the sound of the original playback source, press the SYSTEM CONTROL/FUNCTION button on the remote for that component.

Using the Sleep Timer

You can set the receiver to turn off automatically at a time you specify.

SLEEP

￿￿

Press SLEEP on the remote while the power is on. Each time you press SLEEP, the time changes as shown below.

n2:00:00 n1:30:00n1:00:00 n0:30:00 nOFF

The display dims after you specify the time.

You can freely specify the time

Press SLEEP first, then specify the time you want using DIGITAL PROCESSING CONTROL buttons , , , or . The sleep time changes in 1 minute intervals. You can specify up to 5 hours.

You can check the time remaining before the receiver turns off

Press SLEEP. The remaining time appears in the display.

15EN

Image 15
Contents FM Stereo FM-AM Receiver Precautions Table of Contents Inserting batteries into the remote When to replace batteriesUnpacking Hookup OverviewOverview Connecting a ground wireAntenna Hookups Audio Component HookupsSpeaker System Hookups For even more powerful amplification Selecting the impedanceSelecting the speaker system TV tuner or DBS Digital Broadcasting Satellites receiver To adjust the volumeTV/VCR Hookups What cables will I need?Connecting the AC power cord AC HookupsBefore You Use Your Receiver Selecting a Component 10ENWatching video programs Using the remote Receiving Broadcasts11EN Presetting Radio Stations Receiving broadcasts by scanning stations automatic tuning12EN Tuning preset stations preset tuning Indexing preset stationsIndexing Recording on an audio tape or MiniDisc Scanning indexed stations index tuningRecording Indexing program sourcesReplacing audio while copying a video tape or laser disc Using the Sleep Timer15EN Recording on a video tapeUsing Pre-programmed Sound Fields Introduction16EN 17EN Sound fields for STR-GA8ESSound fields for STR-GA7ES 18EN Selecting the center modeAdjusting the speaker volume Indicator19EN Customizing the Sound Fields Adjusting the equalizer STR-GA8ESAdjusting the tone controls STR-GA7ES You can turn off the tone adjustments without erasing themAdjusting surround sound parameters Resetting customized sound fields to the factory settings21EN 22EN Delay TimeTo reset the setting to the factory setting 23ENNumeric button Operates Programming the Remote Clearing the programmed signalIf the Learn indicator flashes rapidly When you program the recording signal25EN Troubleshooting26EN SpecificationsGeneral Glossary27EN Video section28EN Rear Panel Descriptions 29ENRemote Operates Function Button 30EN31EN 32EN Receiving Preset StationsScanning Preset Stations Scanning Radio StationsPrécautions Au sujet de ce manuel Avant de commencer Mise en place des piles dans la télécommandeDéballage Description des raccordementsRaccordements Raccordement d’antennesRaccordement de composants audio AperçuRaccordement d’enceintes Sélection de l’impédance Sélection du système d’enceintesPour augmenter la puissance d’amplification Moniteur Pour ajuster le volumeRaccordement d’un téléviseur/ magnétoscope Tuner TV ou récepteur DBS télévision numériqueAvant la mise en service de l’ampli-tuner Raccordement au courant secteurBranchement du cordon d’alimentation secteur Sélection d’un composant 10FPour regarder des programmes vidéo Réception radio Utilisation de la télécommandePréréglage des stations de radio 12FRecherche de stations par balayage accord automatique Pour remplacer une station préréglée IndexationAccord des stations préréglées accord préréglé Indexation de stations préréglées14F Balayage des stations indexées accord de stations indexéesIndexation de sources de programme Enregistrement sur une cassette audio ou un minidisque Enregistrement15F Enregistrement sur une cassette vidéoProgrammation de l’arrêt automatique 16FVous pouvez désigner le temps de votre choix 17F Utilisation des champs sonores préréglésChamps sonores du STR-GA7ES 18FChamps sonores du STR-GA8ES PourSi vous avez Sélectionnez Pour que Sélection du mode de canal centralRéglage du volume des enceintes 19F20F Réglage du timbre STR-GA7ES Personnalisation des champs sonoresTemps de réverbération Reverb Réglage de l’égaliseur STR-GA8ESRéglage des paramètres surround 22F23F Paramètres ajustables pour le STR-GA8ESParamètres ajustables pour le STR-GA7ES Programmation de la télécommande Touche numérique Pour sélectionnerPour revenir au réglage usine Télécommande De l’ampli-tuner Environ 5 cm Pouces Effacement d’un signal programméPour programmer un signal d’enregistrement Autre télécommande26F Guide de dépannageSection tuner AM SpécificationsSpécifications de puissance audio Section amplificateur Section tuner FMGénéralités Glossaire28F Section vidéo29F Nomenclature du panneau arrière 30FCommande Contrôle Fonction 31FContrôle Fonction 32F Exemple 1 Lecture d’un CD Balayage desStations préréglées Un disque laser