Runco XP-103DHD, XP-50DHD, XP-OPAL65DHD, XP-OPAL50DHD operation manual Installation Considerations

Page 33

Installation

Proper installation of your PlasmaWall will ensure the highest possible picture quality. Whether you are installing the PlasmaWall temporarily or permanently, you should take the following into account to ensure that it performs optimally.

The extremely large size and high power consumption of the XP-103DHD place unique demands upon both the installation personnel and the installation site, over and above those of the 50-inch and 65-inch PlasmaWall models.

Installing the XP-103DHD requires the following:

•Several people familiar with complex mechanical installations.

•Specialized equipment.

•A dedicated 220VAC circuit.

•A “carry-in” path with sufficient clearances.

•An installation location that can support the weight of both the plasma panel and mounting hardware (floor pedestal or wall mount).

These and other installation requirements are detailed in a document called Runco XP-103DHD Installation Site Pre-Qualification,available from your Runco dealer or representative, or from www.Runco.com. Before proceeding with an XP-103DHD installation, obtain, read and make sure you understand everything in this document.

Due to the design of all plasma glass panels made by every manufacturer, and the interaction between ambient air pressure and the plasma gases contained inside of the panel, reliable operation of your plasma display cannot be assured during operation at certain high-altitude locations.

Runco has found all PlasmaWall models to operate reliably at altitudes of up to 9,000 feet MSL (mean sea level).

At higher elevations, each panel may react differently, depending upon the altitude, air pressure, humidity and other meteorological factors. If you are planning to use this product at a location above 9,000 feet, please contact Runco technical support for further information.

To install the PlasmaWall, you will need either an optional table stand, floor pedestal or wall-mounting kit. (The XP-103DHD must be either wall-mounted or attached to a floor pedestal.)

If you do decide to wall-mount the PlasmaWall, ensure that the wall-mount bracket is installed according to the instructions included with it. The wall must be capable of supporting a redundant weight factor five (5) times the weight of the display, or be reinforced.

Runco recommends that this be done by a custom installation specialist.

Use only a Runco-approved wall-mount kit, table stand or floor

Note pedestal that is specifically designed for your display. Refer to

Parts List on page 4 for ordering information.

3.3 Installation Considerations

Special Requirements for the XP-103DHD

High-Altitude Operation

Mounting the PlasmaWall

on a Wall or Table

Stand/Floor Pedestal

PlasmaWall XP Series Installation/Operation Manual

17

Page 32 Page 34
Image 33
Page 32 Page 34
Contents XP-50DHD XP-OPAL50DHD XP-65DHD XP-OPAL65DHD XP-103DHD Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and TroubleshootingExternal Control SpecificationsTable of Contents Xiv List of Figures PlasmaWall Model XP-65DHD and XP-OPAL65DHD Dimensions About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories XP-50DHD and XP-OPAL50DHD Controls and Indicators Controls and FunctionsPlasmaWall at a Glance STANDBY/ON Indicator Power ButtonRemote Control Sensor Display StandConnectors Shows the rear-panel connector locations on the PlasmaWallDHD Controller Front Panel Down Button Left ButtonRight Button Menu ButtonDHD Controller Rear Panel Outputs 1. Hdmi OutTriggers Main Power Switch InputsMain AC Fuse DHD Controller/PlasmaWall Remote Control PlasmaWall Remote Control UnitEnter IR Output IndicatorReturn / Exit LightSVC CinemaISF Night ISF DAYRemote Control InstallationQuick Setup Installation OverviewStep Procedure For Details, refer to Installation Considerations Ventilation Ambient LightVentilation Requirements for Enclosure Mounting XP-103DHD Possible Audio Latency for Various Input/Output Timings Synchronization IssuesAudio/Video Input Timing Possible Audio Latency millisecondsOther Considerations Connecting PlasmaWall to the DHD Controller Connections to the PlasmaWall and DHD ControllerPlasmaWall Rear Panel RS-232 Connection from the DHD Controller to the PlasmaWall Connecting Source Components to the DHDController DTV-Set-Top Box BD/DVD DTV-STBRGB Camcorder ComputerDVD/DTV STB VCR10. S-Video and Composite Video Source Connections Connection RS-232 Controller12. Connecting 12-volt Trigger Outputs Connecting 12-volt13. External IR Receiver Connection Connecting an External IR Receiver to the DHD Controller14. AC Power Connection Operation Turning on the Power Setting the Computer Display PropertiesOperation Input Position Using the On-Screen MenusRunco Video Main MenuAspect Ratio Input SourceInput Source Aspect RatioRemote Aspect Ratio Control Description Button 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in theirOverscan Remote Aspect Ratio Control Description ButtonPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionAdjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsInformation SignalInformation SystemCalibration Calibration ISF SettingsColor Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsOperation Copy/Paste Copied settings are not retained after a power cycleService ServiceInput Names Exit Operation LCD 47 and ISF Day/Night Memory Presets Operation Cleaning Maintenance and TroubleshootingCleaning the Display Panel Body and Remote Control Cleaning the ScreenTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution To Input Position on Maintenance and Troubleshooting Serial Command Syntax Port ConfigurationExternal Control Serial CommunicationsInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsExit Return key Enter keyUsing Discrete IR Codes Command BitsWith Toggle Bit = Hex Binary Function Start Remote Control With Toggle Description Button Name Bit = IR Command ListRC5 Control Codes for the DHD Controller RC5 DataEnter PlasmaWall Specifications SpecificationsPlasmaWall Specifications XP-OPAL65DHD100 to 240 VAC, 50/60HzDHD Controller Specifications DHD Controller SpecificationsPlasmaWall DimensionsIR Receiver PlasmaWall Model XP-103DHD Dimensions with Floor Stand Format Resolution Frequency Rate Hz MHz KHz Supported Signal Timings by InputSupported Timings Supported? √ = Yes, = NoComponent/ Rgbhv Video 1 S-Video Format Resolution FrequencyVideo Rate Hz MHz KHzPAL-M Page 020-0726-03 rev. a September

XP-OPAL65DHD, XP-OPAL50DHD, XP-50DHD, XP-103DHD specifications

Runco, a pioneer in the field of high-end home theater projectors, has gained a reputation for producing top-tier models that deliver exceptional picture quality and advanced features. Among their notable offerings are the XP-50DHD, XP-OPAL65DHD, XP-OPAL50DHD, and XP-103DHD projectors. Each model showcases Runco's commitment to home cinema excellence through cutting-edge technologies and design.

The Runco XP-50DHD is recognized for its impressive 50-inch display, featuring a native 1080p resolution that ensures sharp and vivid images. This model employs Runco's proprietary InfiniLight technology, providing an intense contrast ratio and remarkable black levels. With Faroudja DCDi Cinema processing, the XP-50DHD excels in scaling lower-resolution content to Full HD, enhancing the viewing experience by eliminating noise and artifacts.

The XP-OPAL65DHD takes performance a step further with a larger 65-inch display and an advanced color management system. This projector incorporates Runco's HDFury technology, allowing for dynamic color management and precise calibration. The result is stunningly accurate color reproduction, making it ideal for home theater enthusiasts who demand the best in color fidelity. Furthermore, the XP-OPAL65DHD supports a wide array of input formats, from traditional HD to 4K, making it versatile enough to handle various content types.

Similarly, the XP-OPAL50DHD offers a 50-inch screen but stands out with its ultra-high-performance optical design. Its advanced lens technology ensures minimal distortion and uniform brightness across the entire image. This model is tailored for those who appreciate both aesthetics and technology in their home setup, featuring a sleek design that seamlessly integrates into any environment.

Lastly, the XP-103DHD projector offers an impressive 103-inch screen size, catering to those who want to replicate a true cinema experience at home. This projector boasts an expansive color gamut and high dynamic range (HDR) capabilities, making it a top choice for cinephiles. With Runco's unique processing algorithms, the XP-103DHD delivers images that pop with vibrancy, depth, and clarity, providing an immersive viewing experience.

Overall, Runco's lineup of XP projectors, including the XP-50DHD, XP-OPAL65DHD, XP-OPAL50DHD, and XP-103DHD, coalesce state-of-the-art technologies and thoughtful design, positioning them as leaders in the luxury projector market. Whether it’s the size, color accuracy, or image processing capabilities, each model exemplifies Runco's dedication to enhancing home theater experiences for discerning users.
Top Page Image Contents