Runco XP-103DHD, XP-50DHD, XP-OPAL65DHD, XP-OPAL50DHD operation manual Calibration ISF Settings

Page 65

Use the Calibration menu to perform advanced picture quality adjustments. This menu should be used by ISF-certified technicians only.

You must enter a passcode to access the Calibration menu.

Note

To recall the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the Memory Presets menu (see page 47) or use the corresponding remote control buttons.

Display Color: Use the Display Color settings to adjust the color balance at the DHD Controller output. These settings are saved independently for each input and display mode.

•Gain: Use the Gain controls to correct color imbalances in the bright areas of the image. A good way to do this is to use a test pattern consisting mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red (Pr), green (Y) or blue (Pr), decrease the Gain for that color.

•Offset: Use the Offset controls to correct color imbalances in the dark areas of the image. A good way to do this is to use a test pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray areas contain traces of red (Pr), green (Y) or blue (Pr), decrease the Offset for that color.

•Gamma: Select Gamma from the Display Color menu to choose a de-gamma curve. Used correctly, the Gamma control can improve contrast while maintaining good details for blacks and whites. If excess ambient light washes out the image and it becomes difficult or impossible to see details in dark areas, lower the gamma setting to compensate. This improves contrast while maintaining good details for blacks. Conversely, if the image is washed out and unnatural, with excessive detail in black areas, increase the setting.

Select S-Curveto emphasize mid-level (gray area) detail, relative to the black and white areas of the image.

Calibration

Calibration

ISF Settings

Display Color

Input Image

Input Color

Save ISF Night

Save ISF Day

Copy/Paste

Output Shift

Splash Configure

OSD Position

PlasmaWall XP Series Installation/Operation Manual

49

Page 64 Page 66
Image 65
Page 64 Page 66
Contents XP-50DHD XP-OPAL50DHD XP-65DHD XP-OPAL65DHD XP-103DHD Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and TroubleshootingExternal Control SpecificationsTable of Contents Xiv List of Figures PlasmaWall Model XP-65DHD and XP-OPAL65DHD Dimensions About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories XP-50DHD and XP-OPAL50DHD PlasmaWall at a Glance Controls and IndicatorsControls and Functions STANDBY/ON Indicator Power ButtonRemote Control Sensor Display StandConnectors Shows the rear-panel connector locations on the PlasmaWallDHD Controller Front Panel Down Button Left ButtonRight Button Menu ButtonTriggers DHD Controller Rear PanelOutputs 1. Hdmi Out Main AC Fuse Main Power SwitchInputs DHD Controller/PlasmaWall Remote Control PlasmaWall Remote Control UnitEnter IR Output IndicatorReturn / Exit LightSVC CinemaISF Night ISF DAYRemote Control InstallationStep Procedure For Details, refer to Quick SetupInstallation Overview Installation Considerations Ventilation Ambient LightVentilation Requirements for Enclosure Mounting XP-103DHD Possible Audio Latency for Various Input/Output Timings Synchronization IssuesAudio/Video Input Timing Possible Audio Latency millisecondsOther Considerations PlasmaWall Rear Panel Connecting PlasmaWall to the DHD ControllerConnections to the PlasmaWall and DHD Controller RS-232 Connection from the DHD Controller to the PlasmaWall Controller Connecting SourceComponents to the DHD DTV-Set-Top Box BD/DVD DTV-STBRGB Camcorder ComputerDVD/DTV STB VCR10. S-Video and Composite Video Source Connections Connection RS-232 Controller12. Connecting 12-volt Trigger Outputs Connecting 12-volt13. External IR Receiver Connection Connecting an External IR Receiver to the DHD Controller14. AC Power Connection Operation Turning on the Power Setting the Computer Display PropertiesOperation Input Position Using the On-Screen MenusRunco Video Main MenuAspect Ratio Input SourceInput Source Aspect RatioRemote Aspect Ratio Control Description Button 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in theirOverscan Remote Aspect Ratio Control Description ButtonPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionAdjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsInformation SignalInformation SystemCalibration Calibration ISF SettingsColor Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsOperation Copy/Paste Copied settings are not retained after a power cycleInput Names ServiceService Exit Operation LCD 47 and ISF Day/Night Memory Presets Operation Cleaning Maintenance and TroubleshootingCleaning the Display Panel Body and Remote Control Cleaning the ScreenSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart To Input Position on Maintenance and Troubleshooting Serial Command Syntax Port ConfigurationExternal Control Serial CommunicationsInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsExit Return key Enter keyWith Toggle Bit = Hex Binary Function Start Using Discrete IR CodesCommand Bits Remote Control With Toggle Description Button Name Bit = IR Command ListRC5 Control Codes for the DHD Controller RC5 DataEnter PlasmaWall Specifications SpecificationsPlasmaWall Specifications XP-OPAL65DHD100 to 240 VAC, 50/60HzDHD Controller Specifications DHD Controller SpecificationsPlasmaWall DimensionsIR Receiver PlasmaWall Model XP-103DHD Dimensions with Floor Stand Format Resolution Frequency Rate Hz MHz KHz Supported Signal Timings by InputSupported Timings Supported? √ = Yes, = NoComponent/ Rgbhv Video 1 S-Video Format Resolution FrequencyVideo Rate Hz MHz KHzPAL-M Page 020-0726-03 rev. a September

XP-OPAL65DHD, XP-OPAL50DHD, XP-50DHD, XP-103DHD specifications

Runco, a pioneer in the field of high-end home theater projectors, has gained a reputation for producing top-tier models that deliver exceptional picture quality and advanced features. Among their notable offerings are the XP-50DHD, XP-OPAL65DHD, XP-OPAL50DHD, and XP-103DHD projectors. Each model showcases Runco's commitment to home cinema excellence through cutting-edge technologies and design.

The Runco XP-50DHD is recognized for its impressive 50-inch display, featuring a native 1080p resolution that ensures sharp and vivid images. This model employs Runco's proprietary InfiniLight technology, providing an intense contrast ratio and remarkable black levels. With Faroudja DCDi Cinema processing, the XP-50DHD excels in scaling lower-resolution content to Full HD, enhancing the viewing experience by eliminating noise and artifacts.

The XP-OPAL65DHD takes performance a step further with a larger 65-inch display and an advanced color management system. This projector incorporates Runco's HDFury technology, allowing for dynamic color management and precise calibration. The result is stunningly accurate color reproduction, making it ideal for home theater enthusiasts who demand the best in color fidelity. Furthermore, the XP-OPAL65DHD supports a wide array of input formats, from traditional HD to 4K, making it versatile enough to handle various content types.

Similarly, the XP-OPAL50DHD offers a 50-inch screen but stands out with its ultra-high-performance optical design. Its advanced lens technology ensures minimal distortion and uniform brightness across the entire image. This model is tailored for those who appreciate both aesthetics and technology in their home setup, featuring a sleek design that seamlessly integrates into any environment.

Lastly, the XP-103DHD projector offers an impressive 103-inch screen size, catering to those who want to replicate a true cinema experience at home. This projector boasts an expansive color gamut and high dynamic range (HDR) capabilities, making it a top choice for cinephiles. With Runco's unique processing algorithms, the XP-103DHD delivers images that pop with vibrancy, depth, and clarity, providing an immersive viewing experience.

Overall, Runco's lineup of XP projectors, including the XP-50DHD, XP-OPAL65DHD, XP-OPAL50DHD, and XP-103DHD, coalesce state-of-the-art technologies and thoughtful design, positioning them as leaders in the luxury projector market. Whether it’s the size, color accuracy, or image processing capabilities, each model exemplifies Runco's dedication to enhancing home theater experiences for discerning users.
Top Page Image Contents