Runco XP-OPAL50DHD, XP-50DHD, XP-103DHD, XP-OPAL65DHD operation manual Operation

Page 67

Operation

•Black Level: Select Black Level from the Display Color menu to adjust the black level “floor” (lower limit). If blacks appear too gray, set Black Level to a higher value.

•Input Level: Select Input Level from the Display Color menu to adjust the overall, apparent brightness of the displayed image. Its effect is similar to a backlight control on an LCD. If parts of the image are extremely bright and hard to see, lower the Input Level to compensate.

Input Image: The Input Image controls are functionally similar to those in the Picture menu (refer to page 40), but are accessible only by entering the Calibration menu passcode.

The Input Image settings establish the “zero point” for the Picture

Note menu settings, whose values represent offsets from the Input Image settings. For example, if you set Brightness to 10 in this menu, setting Brightness to 10 in the Picture menu results in an actual setting value of 20 (10+10).

Input Color: The Input Color controls are similar to those in the Display Color menu (see above), but adjust the color balance of the incoming signal. These settings are also saved independently for each input and display mode.

•Gain/Offset (HD1, HD2 and Component/SCART inputs only): These controls operate similarly to those in the Display Color menu (described on page 49), but affect the Y, Pb and Pr signal components rather than the red, green and blue channels.

•Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a Composite or S-Video source. Chroma delay in an image causes color shifts to occur to the left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If necessary, adjust this setting to eliminate them.

•Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the Input Color menu. The Noise Filter is useful for clearing up noisy images from 480i video sources.

Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image.

Save ISF Night/Save ISF Day: Whenever you make a change to the ISF settings, you should always save it. Select Save ISF Night or Save ISF Day from the Calibration menu to do this.

PlasmaWall XP Series Installation/Operation Manual

51

Page 66 Page 68
Image 67
Page 66 Page 68
Contents XP-50DHD XP-OPAL50DHD XP-65DHD XP-OPAL65DHD XP-103DHD Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and TroubleshootingExternal Control SpecificationsTable of Contents Xiv List of Figures PlasmaWall Model XP-65DHD and XP-OPAL65DHD Dimensions About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories XP-50DHD and XP-OPAL50DHD Controls and Functions Controls and IndicatorsPlasmaWall at a Glance Display Stand Power ButtonSTANDBY/ON Indicator Remote Control SensorConnectors Shows the rear-panel connector locations on the PlasmaWallDHD Controller Front Panel Menu Button Left ButtonDown Button Right ButtonOutputs 1. Hdmi Out DHD Controller Rear PanelTriggers Inputs Main Power SwitchMain AC Fuse DHD Controller/PlasmaWall Remote Control PlasmaWall Remote Control UnitLight IR Output IndicatorEnter Return / ExitISF DAY CinemaSVC ISF NightRemote Control InstallationInstallation Overview Quick SetupStep Procedure For Details, refer to Installation Considerations Ventilation Ambient LightVentilation Requirements for Enclosure Mounting XP-103DHD Input Timing Possible Audio Latency milliseconds Synchronization IssuesPossible Audio Latency for Various Input/Output Timings Audio/VideoOther Considerations Connections to the PlasmaWall and DHD Controller Connecting PlasmaWall to the DHD ControllerPlasmaWall Rear Panel RS-232 Connection from the DHD Controller to the PlasmaWall Components to the DHD Connecting SourceController DTV-Set-Top Box BD/DVD DTV-STBRGB Camcorder ComputerDVD/DTV STB VCR10. S-Video and Composite Video Source Connections Connection RS-232 Controller12. Connecting 12-volt Trigger Outputs Connecting 12-volt13. External IR Receiver Connection Connecting an External IR Receiver to the DHD Controller14. AC Power Connection Operation Turning on the Power Setting the Computer Display PropertiesOperation Input Position Using the On-Screen MenusRunco Video Main MenuAspect Ratio Input SourceAspect Ratio Input SourceHdtv programs in their Aspect Ratio SettingsRemote Aspect Ratio Control Description Button 169 Select 169 to view 169 DVDsOverscan Remote Aspect Ratio Control Description ButtonPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionAdjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsSystem SignalInformation InformationCalibration Calibration ISF SettingsColor Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsOperation Copy/Paste Copied settings are not retained after a power cycleService ServiceInput Names Exit Operation LCD 47 and ISF Day/Night Memory Presets Operation Cleaning the Screen Maintenance and TroubleshootingCleaning Cleaning the Display Panel Body and Remote ControlTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution To Input Position on Maintenance and Troubleshooting Serial Communications Port ConfigurationSerial Command Syntax External ControlInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsExit Return key Enter keyCommand Bits Using Discrete IR CodesWith Toggle Bit = Hex Binary Function Start RC5 Data IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 Control Codes for the DHD ControllerEnter XP-OPAL65DHD100 to 240 VAC, 50/60Hz SpecificationsPlasmaWall Specifications PlasmaWall SpecificationsDHD Controller Specifications DHD Controller SpecificationsPlasmaWall DimensionsIR Receiver PlasmaWall Model XP-103DHD Dimensions with Floor Stand Supported? √ = Yes, = No Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported TimingsRate Hz MHz KHz Video 1 S-Video Format Resolution FrequencyComponent/ Rgbhv VideoPAL-M Page 020-0726-03 rev. a September

XP-OPAL65DHD, XP-OPAL50DHD, XP-50DHD, XP-103DHD specifications

Runco, a pioneer in the field of high-end home theater projectors, has gained a reputation for producing top-tier models that deliver exceptional picture quality and advanced features. Among their notable offerings are the XP-50DHD, XP-OPAL65DHD, XP-OPAL50DHD, and XP-103DHD projectors. Each model showcases Runco's commitment to home cinema excellence through cutting-edge technologies and design.

The Runco XP-50DHD is recognized for its impressive 50-inch display, featuring a native 1080p resolution that ensures sharp and vivid images. This model employs Runco's proprietary InfiniLight technology, providing an intense contrast ratio and remarkable black levels. With Faroudja DCDi Cinema processing, the XP-50DHD excels in scaling lower-resolution content to Full HD, enhancing the viewing experience by eliminating noise and artifacts.

The XP-OPAL65DHD takes performance a step further with a larger 65-inch display and an advanced color management system. This projector incorporates Runco's HDFury technology, allowing for dynamic color management and precise calibration. The result is stunningly accurate color reproduction, making it ideal for home theater enthusiasts who demand the best in color fidelity. Furthermore, the XP-OPAL65DHD supports a wide array of input formats, from traditional HD to 4K, making it versatile enough to handle various content types.

Similarly, the XP-OPAL50DHD offers a 50-inch screen but stands out with its ultra-high-performance optical design. Its advanced lens technology ensures minimal distortion and uniform brightness across the entire image. This model is tailored for those who appreciate both aesthetics and technology in their home setup, featuring a sleek design that seamlessly integrates into any environment.

Lastly, the XP-103DHD projector offers an impressive 103-inch screen size, catering to those who want to replicate a true cinema experience at home. This projector boasts an expansive color gamut and high dynamic range (HDR) capabilities, making it a top choice for cinephiles. With Runco's unique processing algorithms, the XP-103DHD delivers images that pop with vibrancy, depth, and clarity, providing an immersive viewing experience.

Overall, Runco's lineup of XP projectors, including the XP-50DHD, XP-OPAL65DHD, XP-OPAL50DHD, and XP-103DHD, coalesce state-of-the-art technologies and thoughtful design, positioning them as leaders in the luxury projector market. Whether it’s the size, color accuracy, or image processing capabilities, each model exemplifies Runco's dedication to enhancing home theater experiences for discerning users.
Top Page Image Contents