Runco XP-OPAL65DHD, XP-50DHD, XP-103DHD, XP-OPAL50DHD operation manual Exit

Page 70

Operation

Remote Control: Select Remote Control from the Service menu to change the following settings related to remote control operation.

•Remote Code: Select Remote Code from the Remote Control menu to set the infrared (IR) code set to which the PlasmaWall will respond. By default, it is set to 17. You can change this setting if either:

•Another device in the theater (a DVD player, for example) is responding to commands from the PlasmaWall remote control (Figure 2-5)in ways that are unpredictable or undesirable.

•You have multiple DHD Controllers and want to control them independently, as opposed to broadcasting commands from a single remote to all of them. In this scenario, you can use multiple remotes programmed to use different IR codes. Or, you can use a single remote and change the IR code as needed to address a specific DHD Controller.

Use the DHD Controller front-panel keypad to change the IR code to Tip which the controller will respond. Then, change the code sent by the

remote to match as described below.

When you change a remote code on the PlasmaWall, you must re-program the

PlasmaWall remote control to send that same code. To do this:

1.Press and hold the LIGHT button on the remote control for approximately three seconds, or until the LED on the remote lights solid red.

2.Enter a new two-digit code between 00 and 31 inclusive. Include a leading zero for single-digit codes; for example, enter 9 as “09.”

RETURN

EXIT

3.The LED turns off to confirm the code change. If you enter an invalid code, the LED flashes for three or four seconds. Try again, entering a valid code.

•COMP Key Source: Select COMP Key Source from the Remote Control menu to assign the COMP remote control button to either the Component or SCART input.

Display Device - Configure: The options in the Display Device - Configure menu allow you to change the picture orientation, perform lens adjustments or access other, display-device specific functions.

•Installation – Orientation: Select Installation from the Display Device - Configure menu, then select Orientation to change the picture orientation to suit the method of installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear).

•Diagnostics: Select Diagnostics from the Display Device - Configure menu, then select Red, Green, Blue, Yellow, Cyan or Magenta to display only that color channel (simulating a filter of that color). This can be useful for calibration or measurement purposes.

To restore the normal picture (all colors), select White.

54

PlasmaWall XP Series Installation/Operation Manual

Page 69 Page 71
Image 70
Page 69 Page 71
Contents XP-50DHD XP-OPAL50DHD XP-65DHD XP-OPAL65DHD XP-103DHD Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Maintenance and Troubleshooting OperationSpecifications External ControlTable of Contents Xiv List of Figures PlasmaWall Model XP-65DHD and XP-OPAL65DHD Dimensions Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories XP-50DHD and XP-OPAL50DHD Controls and Functions Controls and IndicatorsPlasmaWall at a Glance Remote Control Sensor Power ButtonSTANDBY/ON Indicator Display StandShows the rear-panel connector locations on the PlasmaWall ConnectorsDHD Controller Front Panel Right Button Left ButtonDown Button Menu ButtonOutputs 1. Hdmi Out DHD Controller Rear PanelTriggers Inputs Main Power SwitchMain AC Fuse PlasmaWall Remote Control Unit DHD Controller/PlasmaWall Remote ControlReturn / Exit IR Output IndicatorEnter LightISF Night CinemaSVC ISF DAYInstallation Remote ControlInstallation Overview Quick SetupStep Procedure For Details, refer to Installation Considerations Ambient Light VentilationVentilation Requirements for Enclosure Mounting XP-103DHD Audio/Video Synchronization IssuesPossible Audio Latency for Various Input/Output Timings Input Timing Possible Audio Latency millisecondsOther Considerations Connections to the PlasmaWall and DHD Controller Connecting PlasmaWall to the DHD ControllerPlasmaWall Rear Panel RS-232 Connection from the DHD Controller to the PlasmaWall Components to the DHD Connecting SourceController BD/DVD DTV-STB DTV-Set-Top BoxComputer RGB CamcorderVCR DVD/DTV STB10. S-Video and Composite Video Source Connections RS-232 Controller ConnectionConnecting 12-volt 12. Connecting 12-volt Trigger OutputsConnecting an External IR Receiver to the DHD Controller 13. External IR Receiver Connection14. AC Power Connection Turning on the Power Setting the Computer Display Properties OperationOperation Using the On-Screen Menus Input PositionMain Menu Runco VideoInput Source Input SourceAspect Ratio Aspect RatioSelect 169 to view 169 DVDs Aspect Ratio SettingsRemote Aspect Ratio Control Description Button 169 Hdtv programs in theirRemote Aspect Ratio Control Description Button OverscanPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionAdjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsInformation SignalInformation SystemCalibration ISF Settings CalibrationColor Temperature Presets and Associated Color Points Color Temperature Preset Associated x/y ValuesOperation Copied settings are not retained after a power cycle Copy/PasteService ServiceInput Names Exit Operation LCD 47 and ISF Day/Night Memory Presets Operation Cleaning the Display Panel Body and Remote Control Maintenance and TroubleshootingCleaning Cleaning the ScreenTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution To Input Position on Maintenance and Troubleshooting External Control Port ConfigurationSerial Command Syntax Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsEnter key Exit Return keyCommand Bits Using Discrete IR CodesWith Toggle Bit = Hex Binary Function Start RC5 Control Codes for the DHD Controller IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 DataEnter PlasmaWall Specifications SpecificationsPlasmaWall Specifications XP-OPAL65DHD100 to 240 VAC, 50/60HzDHD Controller Specifications DHD Controller SpecificationsDimensions PlasmaWallIR Receiver PlasmaWall Model XP-103DHD Dimensions with Floor Stand Supported Timings Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported? √ = Yes, = NoVideo Video 1 S-Video Format Resolution FrequencyComponent/ Rgbhv Rate Hz MHz KHzPAL-M Page 020-0726-03 rev. a September

XP-OPAL65DHD, XP-OPAL50DHD, XP-50DHD, XP-103DHD specifications

Runco, a pioneer in the field of high-end home theater projectors, has gained a reputation for producing top-tier models that deliver exceptional picture quality and advanced features. Among their notable offerings are the XP-50DHD, XP-OPAL65DHD, XP-OPAL50DHD, and XP-103DHD projectors. Each model showcases Runco's commitment to home cinema excellence through cutting-edge technologies and design.

The Runco XP-50DHD is recognized for its impressive 50-inch display, featuring a native 1080p resolution that ensures sharp and vivid images. This model employs Runco's proprietary InfiniLight technology, providing an intense contrast ratio and remarkable black levels. With Faroudja DCDi Cinema processing, the XP-50DHD excels in scaling lower-resolution content to Full HD, enhancing the viewing experience by eliminating noise and artifacts.

The XP-OPAL65DHD takes performance a step further with a larger 65-inch display and an advanced color management system. This projector incorporates Runco's HDFury technology, allowing for dynamic color management and precise calibration. The result is stunningly accurate color reproduction, making it ideal for home theater enthusiasts who demand the best in color fidelity. Furthermore, the XP-OPAL65DHD supports a wide array of input formats, from traditional HD to 4K, making it versatile enough to handle various content types.

Similarly, the XP-OPAL50DHD offers a 50-inch screen but stands out with its ultra-high-performance optical design. Its advanced lens technology ensures minimal distortion and uniform brightness across the entire image. This model is tailored for those who appreciate both aesthetics and technology in their home setup, featuring a sleek design that seamlessly integrates into any environment.

Lastly, the XP-103DHD projector offers an impressive 103-inch screen size, catering to those who want to replicate a true cinema experience at home. This projector boasts an expansive color gamut and high dynamic range (HDR) capabilities, making it a top choice for cinephiles. With Runco's unique processing algorithms, the XP-103DHD delivers images that pop with vibrancy, depth, and clarity, providing an immersive viewing experience.

Overall, Runco's lineup of XP projectors, including the XP-50DHD, XP-OPAL65DHD, XP-OPAL50DHD, and XP-103DHD, coalesce state-of-the-art technologies and thoughtful design, positioning them as leaders in the luxury projector market. Whether it’s the size, color accuracy, or image processing capabilities, each model exemplifies Runco's dedication to enhancing home theater experiences for discerning users.
Top Page Image Contents