Runco XP-103DHD, XP-50DHD, XP-OPAL65DHD, XP-OPAL50DHD operation manual Input Position

Page 61

Use the controls in the Input Position Menu to fine-tune the aspect ratio and image position for the current source.

Note

The input position settings are automatically saved for each input

and resolution.

Left/Right: Select Left/Right from the Input Position menu to shift the projected image horizontally. Press to shift the image to the right; press to shift it to the left.

Up/Down: Select Up/Down from the Input Position menu to shift the projected image vertically. Press to shift the image upward; press to shift it downward.

Width: Select Width from the Input Position menu to change the projected image width. Press to increase the width; press to decrease it.

Height: Select Height from the Input Position menu to change the projected image height. Press to increase the height; press to decrease it.

Overscan/Overscan Mode: Overscan pushes the outside edge of the active picture area of the video signal out beyond the edge of the display area.

Some television programs are produced based on the assumption that older television sets may not display the outer edges of the broadcast picture area. Overscan effectively trims away these inactive, outer edges and enlarges the remaining portion of the image to fill the display area.

For HDTV, DVDs and other video sources, Overscan is generally not necessary or desirable.

This control defines the amount of overscan applied to the image. The range is from

0 to 20. There are two overscan modes:

•In Crop mode, each increment adds a mask at the top, bottom, left and right edges of the source image equal to 0.5% of the displayed horizontal resolution (1% total). A setting of 10, for example, crops the image 5% on all sides or 10% total.

•In Zoom mode, each increment adds a factor to the scaling of the source image so that the vertical and horizontal resolutions are 100% plus 1% increments of the size determined by the aspect ratio function. A setting of 10, for example, zooms in on the image 5% on all sides or 10% total.

Figure 4-6illustrates the effect of each overscan mode setting.

Input Position

Input Position

Left/Right

Up/Down

Width

Height

Overscan

Overscan Mode

Phase

Tracking

PlasmaWall XP Series Installation/Operation Manual

45

Page 60 Page 62
Image 61
Page 60 Page 62
Contents XP-50DHD XP-OPAL50DHD XP-65DHD XP-OPAL65DHD XP-103DHD Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and TroubleshootingExternal Control SpecificationsTable of Contents Xiv List of Figures PlasmaWall Model XP-65DHD and XP-OPAL65DHD Dimensions About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories XP-50DHD and XP-OPAL50DHD Controls and Functions Controls and IndicatorsPlasmaWall at a Glance STANDBY/ON Indicator Power ButtonRemote Control Sensor Display StandConnectors Shows the rear-panel connector locations on the PlasmaWallDHD Controller Front Panel Down Button Left ButtonRight Button Menu ButtonOutputs 1. Hdmi Out DHD Controller Rear PanelTriggers Inputs Main Power SwitchMain AC Fuse DHD Controller/PlasmaWall Remote Control PlasmaWall Remote Control UnitEnter IR Output IndicatorReturn / Exit LightSVC CinemaISF Night ISF DAYRemote Control InstallationInstallation Overview Quick SetupStep Procedure For Details, refer to Installation Considerations Ventilation Ambient LightVentilation Requirements for Enclosure Mounting XP-103DHD Possible Audio Latency for Various Input/Output Timings Synchronization IssuesAudio/Video Input Timing Possible Audio Latency millisecondsOther Considerations Connections to the PlasmaWall and DHD Controller Connecting PlasmaWall to the DHD ControllerPlasmaWall Rear Panel RS-232 Connection from the DHD Controller to the PlasmaWall Components to the DHD Connecting SourceController DTV-Set-Top Box BD/DVD DTV-STBRGB Camcorder ComputerDVD/DTV STB VCR10. S-Video and Composite Video Source Connections Connection RS-232 Controller12. Connecting 12-volt Trigger Outputs Connecting 12-volt13. External IR Receiver Connection Connecting an External IR Receiver to the DHD Controller14. AC Power Connection Operation Turning on the Power Setting the Computer Display PropertiesOperation Input Position Using the On-Screen MenusRunco Video Main MenuAspect Ratio Input SourceInput Source Aspect RatioRemote Aspect Ratio Control Description Button 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in theirOverscan Remote Aspect Ratio Control Description ButtonPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionAdjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsInformation SignalInformation SystemCalibration Calibration ISF SettingsColor Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsOperation Copy/Paste Copied settings are not retained after a power cycleService ServiceInput Names Exit Operation LCD 47 and ISF Day/Night Memory Presets Operation Cleaning Maintenance and TroubleshootingCleaning the Display Panel Body and Remote Control Cleaning the ScreenTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution To Input Position on Maintenance and Troubleshooting Serial Command Syntax Port ConfigurationExternal Control Serial CommunicationsInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsExit Return key Enter keyCommand Bits Using Discrete IR CodesWith Toggle Bit = Hex Binary Function Start Remote Control With Toggle Description Button Name Bit = IR Command ListRC5 Control Codes for the DHD Controller RC5 DataEnter PlasmaWall Specifications SpecificationsPlasmaWall Specifications XP-OPAL65DHD100 to 240 VAC, 50/60HzDHD Controller Specifications DHD Controller SpecificationsPlasmaWall DimensionsIR Receiver PlasmaWall Model XP-103DHD Dimensions with Floor Stand Format Resolution Frequency Rate Hz MHz KHz Supported Signal Timings by InputSupported Timings Supported? √ = Yes, = NoComponent/ Rgbhv Video 1 S-Video Format Resolution FrequencyVideo Rate Hz MHz KHzPAL-M Page 020-0726-03 rev. a September

XP-OPAL65DHD, XP-OPAL50DHD, XP-50DHD, XP-103DHD specifications

Runco, a pioneer in the field of high-end home theater projectors, has gained a reputation for producing top-tier models that deliver exceptional picture quality and advanced features. Among their notable offerings are the XP-50DHD, XP-OPAL65DHD, XP-OPAL50DHD, and XP-103DHD projectors. Each model showcases Runco's commitment to home cinema excellence through cutting-edge technologies and design.

The Runco XP-50DHD is recognized for its impressive 50-inch display, featuring a native 1080p resolution that ensures sharp and vivid images. This model employs Runco's proprietary InfiniLight technology, providing an intense contrast ratio and remarkable black levels. With Faroudja DCDi Cinema processing, the XP-50DHD excels in scaling lower-resolution content to Full HD, enhancing the viewing experience by eliminating noise and artifacts.

The XP-OPAL65DHD takes performance a step further with a larger 65-inch display and an advanced color management system. This projector incorporates Runco's HDFury technology, allowing for dynamic color management and precise calibration. The result is stunningly accurate color reproduction, making it ideal for home theater enthusiasts who demand the best in color fidelity. Furthermore, the XP-OPAL65DHD supports a wide array of input formats, from traditional HD to 4K, making it versatile enough to handle various content types.

Similarly, the XP-OPAL50DHD offers a 50-inch screen but stands out with its ultra-high-performance optical design. Its advanced lens technology ensures minimal distortion and uniform brightness across the entire image. This model is tailored for those who appreciate both aesthetics and technology in their home setup, featuring a sleek design that seamlessly integrates into any environment.

Lastly, the XP-103DHD projector offers an impressive 103-inch screen size, catering to those who want to replicate a true cinema experience at home. This projector boasts an expansive color gamut and high dynamic range (HDR) capabilities, making it a top choice for cinephiles. With Runco's unique processing algorithms, the XP-103DHD delivers images that pop with vibrancy, depth, and clarity, providing an immersive viewing experience.

Overall, Runco's lineup of XP projectors, including the XP-50DHD, XP-OPAL65DHD, XP-OPAL50DHD, and XP-103DHD, coalesce state-of-the-art technologies and thoughtful design, positioning them as leaders in the luxury projector market. Whether it’s the size, color accuracy, or image processing capabilities, each model exemplifies Runco's dedication to enhancing home theater experiences for discerning users.
Top Page Image Contents