Runco CR-26HD, CR-32HDi manual Using This Manual, If you need Turn to

Page 12

Introduction

1.2

Using This Manual

Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury:

Tip

TIPS highlight time-saving short cuts and helpful guidelines for using

certain features.

Note

NOTES emphasize text with unusual importance or special

significance. They also provide supplemental information.

Caution

CAUTIONS alert users that a given action or omitted action can

degrade performance or cause a malfunction.

 

WARNING

WARNINGS appear when a given action or omitted action can result

in damage to the equipment, or possible non-fatal injury to the user.

DANGER!

DANGER appears when a given action can cause severe injury or

death.

 

Use the following table to locate the specific information you need in this manual.

If you need...

... Turn to page:

 

 

Information about obtaining service

iv

 

 

General information about the CR-26HD and

3

CR-32HDi LCD Displays

 

 

 

Installation instructions

13

 

 

First-time configuration instructions

23

 

 

Advanced configuration instructions

38

 

 

Troubleshooting tips

47

 

 

Specifications for the CR-26HD and CR-32HDi

53

LCD Displays

 

 

 

2

Runco CR-26HD/CR-32HDi Owner’s Operating Manual

Image 12
Contents CR-26HD Page ONE Year Limited Warranty RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions DOC Compliance NoticeTable of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Indicators Controls and FunctionsCrystal Series LCD Display at a Glance SpeakersCrystal Series LCD Display Inputs and OutputsInput 2 Audio Input Input 2 Composite Video Input Input 3 Component Video RCA connectors DVI/Computer Input DigitalAudio Input RGB/DVI Atsc DTV InputCrystal Series LCD Display Remote Control Crystal Series LCD Display Remote ControlTimer OFF Button Memory Preset ButtonsOFF / on Numeric ButtonsAspect Ratio Selection Buttons ANA Anamorphic 4X3 StandardLetbox Letterbox Vwide VirtualWideSound Control Buttons Surrnd SurroundMTS/SAP Multichannel Television Sound/Second Audio Program Favorite Channel Selection ButtonsControls and Functions Installation Remote ControlBattery Installation Quick Setup Installation OverviewStep Procedure For Details, refer to Installation Considerations Wall-Mounting the Crystal Series LCD DisplayAmbient Light Other ConsiderationsConnections to the Crystal Series LCD Display Antenna/Cable TV ConnectionDVI Connections Refer to Computer/Video Signal Compatibility on page 56 for Analog RGB ConnectionsInput Connection InputConnector Pin Assignments RS-232 ControllerLeft Side Installation Turning on the Power OperationChanging the OSD Language Setting the PC Display Properties Using the On-Screen Menus Picture Adjust TimerSetup SourceMain Menu SourceAspect Ratio TV Input1 Input2 Input3Aspect Ratio Settings Remote Aspect Ratio Control Description KeyTypical Pluge Pattern for Adjusting Brightness Picture AdjustTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Audio Audio Balance Equalizer Surround Audio Language TV SpeakerTimer Channel Auto Tuning Add/Erase Favorite ChannelTimer On Timer Off Timer Sleep Timer Time Zone ChannelCharacteristics of the incoming signal SetupFCC Ratings and Content Categories Rating/Category DescriptionOffensive language ISF Calibration Picture Adjust White Balance Blue Enable Gamma Baud Rate Command Ack Factory Reset Splash DurationISF Calibration Menu should be used by ISF-certified technicians onlyWhite Balance Gain OffsetCrystal Series LCD Display Splash Screen Using Picture-In-Picture PIP Button on the remote control Available Main and PIP Source CombinationsMain Aspect Size Position PIP Swap Swap TV/AV Mode PIP Images Button on the remote control PIP Audio Programs Swap button on the remote controlSwapping the Main Broadcast Mode Receive Mode Mono Stereo Stereo Sound/SAPCompatibility with Stereo and SAP Audio Broadcasts Mono+SAPOperation Maintenance and Troubleshooting Troubleshooting TipsTroubleshooting Chart Symptom Possible Causes SolutionComputer/Video Signal RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands Command DescriptionSAB Key 0002 0043 Specifications Crystal Series LCD Display SpecificationsCrystal Series LCD Display Specifications Specifications are subject to change without noticeCrystal Series LCD Display Dimensions CR-26HD DimensionsCR-32HDi Dimensions Computer/Video Signal Compatibility Computer/Video Signal Compatibility ChartPage Runco CL-810 Owner’s Operating Manual
Related manuals
Manual 70 pages 38.36 Kb