Runco CR-26HD, CR-32HDi manual Connection, Input

Page 30

Installation

MONITOR OUT ➤	The Crystal Series LCD Display has a monitor out feature for connecting a second VCR or
Connection	other auxiliary equipment. Connect the MONITOR OUT audio and video jacks to the audio
	and video inputs of the VCR or other equipment as shown in Figure 3-6.
	You can route either the main or picture-in-picture (PIP) source signal to the monitor
	outputs. For more information, refer to Monitor Out on page 37.

MONITOR OUT

Figure 3-6. Monitor Output Connections

Connecting Headphones ➤ You can connect a set of headphones to the Crystal Series LCD Display to watch a program without disturbing others. Connect them to the headphone output located at INPUT 2; see Figure 3-7.

Input 2

S-Video

R

Audio

L

Video

Figure 3-7. Connecting Headphones

20	Runco CR-26HD/CR-32HDi Owner’s Operating Manual

Image 30

Contents CR-26HD Page ONE Year Limited Warranty RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions DOC Compliance NoticeTable of Contents Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Crystal Series LCD Display at a Glance Controls and IndicatorsControls and Functions SpeakersCrystal Series LCD Display Inputs and OutputsInput 2 Audio Input Input 2 Composite Video Input Audio Input RGB/DVI Input 3 Component Video RCA connectorsDVI/Computer Input Digital Atsc DTV InputCrystal Series LCD Display Remote Control Crystal Series LCD Display Remote ControlOFF / on Timer OFF ButtonMemory Preset Buttons Numeric ButtonsLetbox Letterbox Aspect Ratio Selection Buttons ANA Anamorphic4X3 Standard Vwide VirtualWideMTS/SAP Multichannel Television Sound/Second Audio Program Sound Control ButtonsSurrnd Surround Favorite Channel Selection ButtonsControls and Functions Installation Remote ControlBattery Installation Quick Setup Installation OverviewStep Procedure For Details, refer to Ambient Light Installation ConsiderationsWall-Mounting the Crystal Series LCD Display Other ConsiderationsConnections to the Crystal Series LCD Display Antenna/Cable TV ConnectionDVI Connections Refer to Computer/Video Signal Compatibility on page 56 for Analog RGB ConnectionsInput Connection InputConnector Pin Assignments RS-232 ControllerLeft Side Installation Turning on the Power OperationChanging the OSD Language Setting the PC Display Properties Using the On-Screen Menus Setup Picture AdjustTimer SourceAspect Ratio Main MenuSource TV Input1 Input2 Input3Aspect Ratio Settings Remote Aspect Ratio Control Description KeyTypical Pluge Pattern for Adjusting Brightness Picture AdjustTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Audio Audio Balance Equalizer Surround Audio Language TV SpeakerTimer On Timer Off Timer Sleep Timer Time Zone TimerChannel Auto Tuning Add/Erase Favorite Channel ChannelCharacteristics of the incoming signal SetupFCC Ratings and Content Categories Rating/Category DescriptionOffensive language ISF Calibration ISF Calibration Picture Adjust White Balance Blue EnableGamma Baud Rate Command Ack Factory Reset Splash Duration Menu should be used by ISF-certified technicians onlyWhite Balance Gain OffsetCrystal Series LCD Display Splash Screen Using Picture-In-Picture PIP Button on the remote control Available Main and PIP Source CombinationsMain Aspect Size Position PIP Swap Swap TV/AV Mode PIP Images Button on the remote control PIP Audio Programs Swap button on the remote controlSwapping the Main Compatibility with Stereo and SAP Audio Broadcasts Broadcast Mode Receive Mode Mono StereoStereo Sound/SAP Mono+SAPOperation Troubleshooting Chart Maintenance and TroubleshootingTroubleshooting Tips Symptom Possible Causes SolutionComputer/Video Signal Serial Commands RS-232 Connection and Port ConfigurationSerial Command Syntax Command DescriptionSAB Key 0002 0043 Crystal Series LCD Display Specifications SpecificationsCrystal Series LCD Display Specifications Specifications are subject to change without noticeCrystal Series LCD Display Dimensions CR-26HD DimensionsCR-32HDi Dimensions Computer/Video Signal Compatibility Computer/Video Signal Compatibility ChartPage Runco CL-810 Owner’s Operating Manual

Related manuals

Manual 70 pages 38.36 Kb