Runco CR-26HD, CR-32HDi Quick Setup, Installation Overview, Step Procedure For Details, refer to

Page 24

Installation

3.2

Quick Setup

Table 3-1gives a quick overview of the Crystal Series LCD Display installation process. The sections following this one provide detailed instructions.

	Note	Installation should be performed by a qualified custom video
		installation specialist.
Table 3-1. Installation Overview

Step		Procedure	For Details, refer to
			page...


1	Mount the Crystal Series LCD Display on a wall (optional)		15

2	Connect signal sources to the Crystal Series LCD Display		16

3	Connect external controller to RS-232 port (optional)		21

4	Apply power to the Crystal Series LCD Display		23

5	Change the OSD language		23

6	If using the Crystal Series LCD Display with a PC, adjust PC		24
	display properties


	Display calibration: adjust the following for each input;		27 through 37
	save settings when finished:

•Brightness

7 • Contrast

•Color level

•Tint

•Input position

14	Runco CR-26HD/CR-32HDi Owner’s Operating Manual

Image 24

Contents CR-26HD Page ONE Year Limited Warranty RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions DOC Compliance NoticeTable of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Indicators Controls and FunctionsCrystal Series LCD Display at a Glance SpeakersCrystal Series LCD Display Inputs and OutputsInput 2 Audio Input Input 2 Composite Video Input Input 3 Component Video RCA connectors DVI/Computer Input DigitalAudio Input RGB/DVI Atsc DTV InputCrystal Series LCD Display Remote Control Crystal Series LCD Display Remote ControlTimer OFF Button Memory Preset ButtonsOFF / on Numeric ButtonsAspect Ratio Selection Buttons ANA Anamorphic 4X3 StandardLetbox Letterbox Vwide VirtualWideSound Control Buttons Surrnd SurroundMTS/SAP Multichannel Television Sound/Second Audio Program Favorite Channel Selection ButtonsControls and Functions Installation Remote ControlBattery Installation Quick Setup Installation OverviewStep Procedure For Details, refer to Installation Considerations Wall-Mounting the Crystal Series LCD DisplayAmbient Light Other ConsiderationsConnections to the Crystal Series LCD Display Antenna/Cable TV ConnectionDVI Connections Refer to Computer/Video Signal Compatibility on page 56 for Analog RGB ConnectionsInput Connection InputConnector Pin Assignments RS-232 ControllerLeft Side Installation Turning on the Power OperationChanging the OSD Language Setting the PC Display Properties Using the On-Screen Menus Picture Adjust TimerSetup SourceMain Menu SourceAspect Ratio TV Input1 Input2 Input3Aspect Ratio Settings Remote Aspect Ratio Control Description KeyTypical Pluge Pattern for Adjusting Brightness Picture AdjustTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Audio Audio Balance Equalizer Surround Audio Language TV SpeakerTimer Channel Auto Tuning Add/Erase Favorite ChannelTimer On Timer Off Timer Sleep Timer Time Zone ChannelCharacteristics of the incoming signal SetupFCC Ratings and Content Categories Rating/Category DescriptionOffensive language ISF Calibration Picture Adjust White Balance Blue Enable Gamma Baud Rate Command Ack Factory Reset Splash DurationISF Calibration Menu should be used by ISF-certified technicians onlyWhite Balance Gain OffsetCrystal Series LCD Display Splash Screen Using Picture-In-Picture PIP Button on the remote control Available Main and PIP Source CombinationsMain Aspect Size Position PIP Swap Swap TV/AV Mode PIP Images Button on the remote control PIP Audio Programs Swap button on the remote controlSwapping the Main Broadcast Mode Receive Mode Mono Stereo Stereo Sound/SAPCompatibility with Stereo and SAP Audio Broadcasts Mono+SAPOperation Maintenance and Troubleshooting Troubleshooting TipsTroubleshooting Chart Symptom Possible Causes SolutionComputer/Video Signal RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands Command DescriptionSAB Key 0002 0043 Specifications Crystal Series LCD Display SpecificationsCrystal Series LCD Display Specifications Specifications are subject to change without noticeCrystal Series LCD Display Dimensions CR-26HD DimensionsCR-32HDi Dimensions Computer/Video Signal Compatibility Computer/Video Signal Compatibility ChartPage Runco CL-810 Owner’s Operating Manual

Related manuals

Manual 70 pages 38.36 Kb