Runco CR-26HD, CR-32HDi manual Analog RGB Connections

Page 28

Installation

RGB Connections: The Crystal Series LCD Display has an RGB input for connecting a personal computer; see Figure 3-3.

Rear of the Display

Rear of the PC

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

Audio Cable

(Sold Separately)

D-Sub 15 Pin Cable (Sold Separately)

Figure 3-3. Analog RGB Connections

1. Refer to Computer/Video Signal Compatibility on page 56 for

Note

a list of computer signals compatible with the Crystal Series LCD

 

 

Display. Use with signals other than those listed may cause some

 

functions not to work.

2.Some Macintosh computers may require a Macintosh video adapter. Contact your nearest authorized service center or dealer.

3.This Crystal Series LCD Display may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, switch the notebook computer to “CRT only” mode. If you are unsure how to do this, refer to your notebook computer’s user manual.

18

Runco CR-26HD/CR-32HDi Owner’s Operating Manual

Image 28
Contents CR-26HD Page ONE Year Limited Warranty RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions DOC Compliance NoticeTable of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Indicators Controls and FunctionsCrystal Series LCD Display at a Glance SpeakersInputs and Outputs Crystal Series LCD DisplayInput 2 Audio Input Input 2 Composite Video Input Input 3 Component Video RCA connectors DVI/Computer Input DigitalAudio Input RGB/DVI Atsc DTV InputCrystal Series LCD Display Remote Control Crystal Series LCD Display Remote ControlTimer OFF Button Memory Preset ButtonsOFF / on Numeric ButtonsAspect Ratio Selection Buttons ANA Anamorphic 4X3 StandardLetbox Letterbox Vwide VirtualWideSound Control Buttons Surrnd SurroundMTS/SAP Multichannel Television Sound/Second Audio Program Favorite Channel Selection ButtonsControls and Functions Remote Control InstallationBattery Installation Installation Overview Quick SetupStep Procedure For Details, refer to Installation Considerations Wall-Mounting the Crystal Series LCD DisplayAmbient Light Other ConsiderationsConnections to the Crystal Series LCD Display Antenna/Cable TV ConnectionDVI Connections Refer to Computer/Video Signal Compatibility on page 56 for Analog RGB ConnectionsInput Connection InputRS-232 Controller Connector Pin AssignmentsLeft Side Installation Operation Turning on the PowerChanging the OSD Language Setting the PC Display Properties Using the On-Screen Menus Picture Adjust TimerSetup SourceMain Menu SourceAspect Ratio TV Input1 Input2 Input3Aspect Ratio Settings Remote Aspect Ratio Control Description KeyTypical Pluge Pattern for Adjusting Brightness Picture AdjustTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Audio Audio Balance Equalizer Surround Audio Language TV SpeakerTimer Channel Auto Tuning Add/Erase Favorite ChannelTimer On Timer Off Timer Sleep Timer Time Zone ChannelCharacteristics of the incoming signal SetupFCC Ratings and Content Categories Rating/Category DescriptionOffensive language ISF Calibration Picture Adjust White Balance Blue Enable Gamma Baud Rate Command Ack Factory Reset Splash DurationISF Calibration Menu should be used by ISF-certified technicians onlyWhite Balance Gain OffsetCrystal Series LCD Display Splash Screen Using Picture-In-Picture PIP Available Main and PIP Source Combinations Button on the remote controlMain Aspect Size Position PIP Swap Swap TV/AV Mode PIP Audio Programs Swap button on the remote control PIP Images Button on the remote controlSwapping the Main Broadcast Mode Receive Mode Mono Stereo Stereo Sound/SAPCompatibility with Stereo and SAP Audio Broadcasts Mono+SAPOperation Maintenance and Troubleshooting Troubleshooting TipsTroubleshooting Chart Symptom Possible Causes SolutionComputer/Video Signal RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands Command DescriptionSAB Key 0002 0043 Specifications Crystal Series LCD Display SpecificationsCrystal Series LCD Display Specifications Specifications are subject to change without noticeCrystal Series LCD Display Dimensions CR-26HD DimensionsCR-32HDi Dimensions Computer/Video Signal Compatibility Computer/Video Signal Compatibility ChartPage Runco CL-810 Owner’s Operating Manual
Related manuals
Manual 70 pages 38.36 Kb