Sanyo DSR-3506P manual Controlling from the unit, Messages displayed when connected

Page 8

2PREPARING FOR NETWORK CONTROL

Controlling from the unit

Whenever the button on the PC’s operation screen is clicked, access will be cancelled and control rights will switch back to the unit.

zTo forcibly cancel PC access from the unit, press and hold the [EXIT] button for at least 2 seconds.

zAccess from the PC will not be permitted for a period of 10 seconds after access has been canceled.

zThe access connection will also be cancelled whenever communication with the PC is not possible for a period of about 1 minute or more, and control rights will switch back to the unit in such a case.

zIf the browser is closed without clicking the button, approximately one minute is required before reconnection is possible.

Messages displayed when connected

Messages related to the switching of control or the network connection condition may be displayed on-screen at any time.

Display on the unit

1 When control rights are switched to the

PC

“NETWORK CONTROL” appears on the monitor.

01-01-04 00:00:00 REC REPEAT EN A ALARM 0000

NETWORK CONTROL

02

zThe “NETWORK CONTROL” message is not displayed when “NETWORK STATUS” has been set to “OFF” using the unit’s menu. (Regardless of network operations, the unit will continue to display images.)

2 When control rights are switched to the unit

Whenever the button on the PC’s operation screen is clicked, access will be cancelled and control rights will switch back to the unit. In addition, the “NETWORK CONTROL” message from the unit’s on-screen display will be changed to “DISCONNECTED”.

zOnce the message has changed to “DISCONNECTED”, it can be cleared by pressing any of the unit’s buttons.

01-01-04 00:00:00 REC REPEAT EN A ALARM 0000

DISCONNECTED

02

3 Forced disconnection from the unit

To forcibly cancel access by a PC, press and hold the unit’s [EXIT] button for at least 2 seconds. When access is forcibly cancelled in this way, the “NETWORK CONTROL” message will be replaced with “DISCONNECTED”.

zAccess from the PC will not be permitted for a period of 10 seconds after access has been canceled.

Display on the PC

1 When disconnected from the network

2 When access cannot be made to a connected DVR

3 When accessing a DVR that is already connected to another 4 PCs

English

7

Image 8
Contents Page Contents Network settings Network Control FunctionOperations possible with PC control Saving and playing back soundInstalling DVR Viewer Setting Internet OptionsNetwork Control Function Click the Security tabClick OK Click Network ConnectionsClick Properties Enter a password for verification purposes Preparing for Network ControlControlling from a PC Launch the PC’s web browserPreparing for Network Control Entering the operation screenMessages displayed when connected When control rights are switched toWhen control rights are switched to the unit Controlling from the unitSetting buttons Operation panelChannel and screen selection buttons Playback buttonsSettings Making menu selectionClick the button on the operation panel Main Menu screen is displayedSettings Menu structureSummer Time SET/EXT. Clock SET MENU-SPECIFIC SettingsClock SET MENU-SPECIFIC Settings Holiday SET Saved or modified settings are storedMENU-SPECIFIC Settings Recording Area SET Recording area resetTotal capacity display Area-specific capacity displayMENU-SPECIFIC Settings Recording Conditions SET Setting overwriting permission for the alarm recording areaSetting the remaining-space warning level Setting the auto deleteMENU-SPECIFIC Settings Normal REC Mode SET Setting the picture quality for recordingSetting audio recording Setting the recording rateMENU-SPECIFIC Settings Program REC SET Use the above procedure to set up to four program patternsSelect Program from the pull-down menu on the screen Select from P-1 through P-4MENU-SPECIFIC Settings Timer SET „ Performing timer recording„ Overlapping of timer reservation times „ Setting a timer for over 24-hours continuous recordingMENU-SPECIFIC Settings Alarm REC Mode SET Setting alarm recordingSetting the alarm interleave Set the recording conditions for alarm recording as followsMENU-SPECIFIC Settings Setting pre-alarm recordingDefault setting A15 FPS SettingsSetting alarm triggers External alarm detectionDisplay SET Motion sensor detectionMENU-SPECIFIC Settings Buzzer SET Select on or OFF for the alarm buzzerNew settings are saved To cancel sounding of a buzzer on the PCMENU-SPECIFIC Settings HDD SET Change the settings as requiredNetwork SET MirroringPassword Setting Use between 4 and 8 alphanumeric characters for passwordsNetwork settings or modifications are saved RS-485 SETMENU-SPECIFIC Settings Mask SET Power FAILURE/USED TimeSetting is saved Initialized RecordTimer recording Alarm recordingPre-alarm recording Recording ImagesRecording Images Screen display items10Connection user Normal Recording ModeAlarm Recording Mode Playing back recorded images Watching ImagesWatching live images during playback Specifying the number of screens to display Performing operations in play modeWatching Images Adjusting the image and audio Live mode image Multi channels Play mode image 1 channelSettings for downloading live images to a PC Alarm PRE-ALRAM Normal Archive12SPEED in the play mode screen only Save setting items are displayed„ To cancel a save operation Set DurationClick Browse Click StartSearch Mode Search for images using the search mode screenBasic operation Search menuOperations in Search Modes Alarm SearchAlarm Thumbnail Search Operations in Search Modes TIME/DATE Search Archive Area SearchSelect 3. TIME/DATE Search from the Search menu Click PreviewSelect 5. Motion Detection Search from the Search menu Setting motion sensor detection conditionsOperations in Search Modes Motion Detection Search Saving Recorded Images Copying to the archive areaClick Input the number of images into HOW ManySaving Recorded Images Downloading to a PCSelect the Audio Click OK Specify a location for storing the dataImage viewer screen Operating environment Installing the DVR ViewerDVR Viewer Opening and closing DVR Viewer Opening DVR ViewerClosing DVR Viewer Menu barOpening files Click Open O in the File F menuToolbar Alternatively, click the icon on the toolbarViewing images Main windowThumbnail window Control panel JP11IMAGE Number TOPPrev Printing images To print the image in the main windowTo print thumbnail images To print several images all at once
Related manuals
Manual 112 pages 54.62 Kb