Zenith H20H52DT, HW20H52DT warranty Before you begin

Page 40

LT2000 QuickSet Programmer

Before you begin:

The “master TV” should be connected to a good, stable signal from an over-the-air antenna or cable service and turned on.

Teaching and Learning is only possible between identical model Zenith TVs. (However, the Clone programmer can store 4 different master TV setups.)

WARNING: Copying a blank or incorrect memory into a TV will cause the TV to operate erratically or become inoperable.

Use a Zenith MBR Remote like the MBR3447 or the TV front panel controls to operateM Learning and Teaching menus.

Make sure that the batteries in the Clone programmer are fresh.

If the batteries are removed, the Clone Clock time will be lost.

Decide if you want to set the time from the Clone programmer or copy the time to the Clone programmer; from a TV which has the clock set to the current time.

Follow the connection diagrams above to connect the Clone to a master TV and, after learning is complete, to another TV to “teach” it the setup.

Setting the time and transferring it to the Clone or another TV is a separate procedure.

Once a TV’s setup is copied to another TV, that TV needs to be disconnected from power for about 5 seconds to activate the newly copied setup.

See Troubleshooting to solve problems.

A. Set Up a Master TV

Using a Zenith Multi-Brand remote like the MBR3447, set up a “Master” TV with custom settings and features as described in the master Tv’s operating guide. The master TV’s Setup is what you will copy to the Clone Programmer and transfer to TVs of the same model so they will operate identically.

B. Connect Clone to Master TV

If there is a good connection, the “Clone has Control of TV” message will appear. (See menu above.)

A slow flashing green light indicates there is a problem with the communications between the TV and the programmer. In this case, check for a damaged cable, poor contacts, or other connection troubles.

If the status indicator is red, the programmer batteries are low and should be replaced. Use 4 good-quality alkaline AA batteries.

Page 40

Image 40
Contents Installation a n d O p e r a t i n g G u i d e R r a n t y B l e o f c o n t e n t s G eModel NO. H20H52DT/HW20H52DT Important Safety Instructions From previous Table of Contents Antenna Hook Up Connect an off-air antenna to the HealthView TVCable Service Catv Hook Up Connect cable service to the HealthView TVAntenna with VCR Hook Up Connect an off-air antenna and VCR to the HealthView TVCable Service Catv with VCR Hook Up Connect Cable service and a VCR to the HealthView TVExternal Speaker Connection 8-ohm Connect Speaker out to an 8-ohm speaker as shownPillow Speaker Hook Up Connect a Pillow Speaker to the HealthView TVAuto Program Channel Search Using the front control panel to operate the television Front Panel ControlsInstaller Remote Key Functions MuteInstaller Menus On-Screen Menus OverviewDescriptions of the menus on the TV Other Menus and ON-SCREEN DisplaysSetting Up Channel Line Up/Add/Delete/Blank Fine-tune the patient’s channel selection listEnter to remove menu Channel Preview ListSetting Up Channel Labels Setup MenuClock Mode Clock Auto/Manual Operating Modes SetupClock Set Setting On/Off Timers TimerClosed Captions/Text Operating Modes Setup Set up Closed Caption/Text options for the userCaptions Captions/Text Language Choose the language for the on-screen menusUse the Video menu to customize the picture appearance Video MenuPicture Preference FM Radio Menu Use the FM Menu to customize FM Radio optionsFM Setup Menu Options Descriptions of the FM Radio Installer’s menusRadio Menu Options Installer Parental Control Menu Things To Consider Before Setting Up Parental ControlUse the installer’s remote Other Menus & On-Screen Displays Channel Banks MenuManaging the Channel Banks Planning the Channel BanksAdding / Deleting Channels Inactive TV Display Channel BankExamples of typical channel banks chart Channel Number Installer Menus Using the Installer’s MenuInstaller Menu Item 26-I through Brief Description of Function and CommentsDetailed Descriptions of Installer Menu Items Installer SequencePower Manage Power Management AC on AC Power SwitchableInstaller Menu Item 4-I through 13-I Detailed Descriptions Start Volume10-I. Mute Disable 13-I. Scan Mode15-I. Sleep Timer 16-I. EN. Timer17-I. Alarm 19-I. not Used 20-I. Feature LevelInstaller Menu Item 28-I through 59-I Detailed Descriptions 60-I. EN. VIDEO. COL 66-I. not Used 67-I. not Used 68-I. not Used72-I. not Used 73-I. CH not Avble 74-I. CH-TIME SizeInstaller Menu Item 79-I through 90-I Detailed Descriptions LT2000 QuickSet Programmer Learn Master TV Typical MPI ConnectionsBefore you begin Clone Selection Menu Choices Typical Edit Channel Labels on-screen menusLearn Setup from Master TV Teach Master TV’s Setup to Other TVDisconnect TV Power for 5 Seconds Ca. Set the Clock OptionalOperation Notes Reset Clone After Static ShockMaster and Other TVs Patient Remote Key Functions Volume UP/DOWN Patient Remote Key Functions-FM RadioParental Control Menu Motion Picture Association of America Mpaa Rating SystemInformation Menus & On-Screen Displays Ch Preview MenuMaintenance Routine TV cabinet and screen cleaningTroubleshooting Some quick and easy tips to resolving problemsGlossary Warranty OWNER’S Responsibility