Zenith HW20H52DT, H20H52DT warranty Installer Menus, Using the Installer’s Menu

Page 31

Installer Menus

Use the Installer’s Menus to make TV operation adjustments.

Accessing the Installer’s Menu

Installer’s menus can be accessed by using the optional installer’s remote control. Just press and hold MENU (about 8 seconds) until the display changes, then press 9, 8, 7, 6, then ENTER. To exit the Installer’s Menu, press ENTER again. Changes you make will be stored in nonvolatile memory.

The Installer’s Menu opens with item 00-I, INST. SEQ. Use the SELECT key to sequence through the available menu items. Or, access an item directly by entering the line number, then pressing MENU. For example, to access the Start Channel option which is on line 11, press 11, then MENU. To change a current setting use the Left/Right ADJ keys.

OIMCRMIO62A 01.48

01

00-I.

INST . SEQ.

0

SN:XXXX-XXXXXXXX UPN:XXX-XXX-XXX-XXX XX/XX/XX TE = 10110000

Using the Installer’s Menu

Items 00-90 are immediately accessible only upon entering the Installer’s Menu. Their numbers, descriptions, ranges, factory default settings, and a place for listing any changes made on-site are given below. A second section of the Installer’s Menu that is intended for qualified service technicians only is not shown (XX-F Items). Normally these items do not require adjustment.

Items in the Installer’s Menu: 0-I to 25-I

XX-F Menu Items (Not shown here) are service-type adjustments and only qualified technicians having specialized test equipment should access them.

Menu Item

Function

Value Range

Default Value

Brief Description of Function and Comments

0-I.

INSTALLER. SEQ

0 - 3

0

Changes installer Entry Sequece. Leave default set 0

 

 

 

 

0 ( 9876), 1 (4321), 2 (1478), 3 (3698)

1-I.

POWER MANAGE

0 - 7

0

Sets number of hours of no activity before auto shutoff.

2-I.

AC ON

0 / 1

0

Set to 1 to enable auto turn on at power up.

3-I.

BAND/AFC

0 - 7

0

Tuning band, see detailed descriptions.

4-I.

STRT CHANNEL

0 - 255

255

Channel at turn-on (255 last Ch).

5-I.

CHAN LOCK

0 / 1

0

When set to 1, cannot tune from current channel.

6-I.

GHOST CH

0 / 1

0

Set to 1 to enable Ghost Channel display.

7-I.

START VOLUME

0 - 63, 255

255

Volume level at TV turn-on (Set 255 to r etain last volume level).

8-I.

MIN VOLUME

0 - 63

0

Minimum volume setting.

9-I.

MAX VOLUME

0 - 63

63

Maximum volume setting.

10-I.

MUTE DISABLE

0 / 1

0

Set to 1 to disable m ute function.

11-I.

KEY DEFEAT

0 / 1

1

Set to 1 to disable M enu, Select, and Adj keys on front panel.

12-I.

IR BANKS EN.

0 / 1

0

Set to 1: enables TV to respond to IR codes to change Channel Bank directly.

13-I.

SCAN MODE

0 - 3

1

Typically used for Hospitals: puts On-Off and FM in Ch Up/Down sequen ce.

14-I.

STRT CH IN SM

0 / 1

0

Set to 1 to put TV on/o ff below start channel number.

15-I.

SLEEP TIMER

0 / 1

1

Set to 1 to enable Sleep Timer.

16-I.

EN. TIMER

0 / 1

1

Set to 1 to enable Timer.

17-I.

ALARM

0 / 1

1

Set to 1 to enable Alarm.

18-I.

RADIO

0 / 1

1

Set to 1 for TVs with Radio.

19-I.

NOT USED

 

 

 

20-I.

FEATURE LEVEL

0 / 1

1 Zen 1

Leave default set 1 (1 Zen 1)

21-I.

V-CHIP

0 / 1

1

Set to 1 to enable V-Chip

22-I.

MAX BLK HRS

0 - 99

12

Select number of Parental Control blocking hours.

23-I.

CAPTION LOCK

0 / 1

0

Set to 1 to retain caption setting at turn off.

24-I.

TEXT MODE

0 / 1

1

Set to 1 to add Text option to closed caption menu.

25-I.

FUNCTION PRE.0

0 - 3

0

Controls channel preview in Pay-Per-View function menu.

 

 

 

 

 

Page 31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents B l e o f c o n t e n t s G e Installation a n d O p e r a t i n g G u i d e R r a n t yModel NO. H20H52DT/HW20H52DT Important Safety Instructions From previous Table of Contents Connect an off-air antenna to the HealthView TV Antenna Hook UpConnect cable service to the HealthView TV Cable Service Catv Hook UpConnect an off-air antenna and VCR to the HealthView TV Antenna with VCR Hook UpConnect Cable service and a VCR to the HealthView TV Cable Service Catv with VCR Hook UpConnect Speaker out to an 8-ohm speaker as shown External Speaker Connection 8-ohmConnect a Pillow Speaker to the HealthView TV Pillow Speaker Hook UpAuto Program Channel Search Front Panel Controls Using the front control panel to operate the televisionMute Installer Remote Key FunctionsOther Menus and ON-SCREEN Displays Installer MenusOn-Screen Menus Overview Descriptions of the menus on the TVChannel Preview List Setting Up Channel Line Up/Add/Delete/BlankFine-tune the patient’s channel selection list Enter to remove menuSetup Menu Setting Up Channel LabelsClock Mode Clock Auto/Manual Operating Modes SetupClock Set Timer Setting On/Off TimersClosed Captions/Text Operating Modes Setup Set up Closed Caption/Text options for the userCaptions Captions/Text Choose the language for the on-screen menus LanguageUse the Video menu to customize the picture appearance Video MenuPicture Preference Use the FM Menu to customize FM Radio options FM Radio MenuFM Setup Menu Options Descriptions of the FM Radio Installer’s menusRadio Menu Options Things To Consider Before Setting Up Parental Control Installer Parental Control MenuUse the installer’s remote Channel Banks Menu Other Menus & On-Screen Displays Inactive TV Display Channel Bank Managing the Channel Banks Planning the Channel Banks Adding / Deleting ChannelsExamples of typical channel banks chart Channel Number Using the Installer’s Menu Installer MenusBrief Description of Function and Comments Installer Menu Item 26-I throughAC on AC Power Switchable Detailed Descriptions of Installer Menu ItemsInstaller Sequence Power Manage Power Management13-I. Scan Mode Installer Menu Item 4-I through 13-I Detailed DescriptionsStart Volume 10-I. Mute Disable19-I. not Used 20-I. Feature Level 15-I. Sleep Timer16-I. EN. Timer 17-I. AlarmInstaller Menu Item 28-I through 59-I Detailed Descriptions 74-I. CH-TIME Size 60-I. EN. VIDEO. COL66-I. not Used 67-I. not Used 68-I. not Used 72-I. not Used 73-I. CH not AvbleInstaller Menu Item 79-I through 90-I Detailed Descriptions Learn Master TV Typical MPI Connections LT2000 QuickSet ProgrammerBefore you begin Typical Edit Channel Labels on-screen menus Clone Selection Menu ChoicesCa. Set the Clock Optional Learn Setup from Master TVTeach Master TV’s Setup to Other TV Disconnect TV Power for 5 SecondsOperation Notes Reset Clone After Static ShockMaster and Other TVs Patient Remote Key Functions Patient Remote Key Functions-FM Radio Volume UP/DOWNMotion Picture Association of America Mpaa Rating System Parental Control MenuInformation Ch Preview Menu Menus & On-Screen DisplaysRoutine TV cabinet and screen cleaning MaintenanceSome quick and easy tips to resolving problems TroubleshootingGlossary OWNER’S Responsibility Warranty
Top Page Image Contents