Magnavox VRX562AT99 warranty Hookups With a Cable Box/DSS Receiver, Recording/Viewing Any Channel

Page 8

8 Hookups With a Cable Box/DSS Receiver

This connection allows you to view any channel. After you connect the Cable Box/DSS Receiver, VCR, and TV as shown below, the features described on this page will be available.

1.Connect a Cable signal to the IN Jack on the Cable Box/DSS Receiver.

IN

OUT

AUDIO

ANT

IN

L

 

OUT

 

VIDEO

OUT

OUT

IN CH3

CH4

2. Use an RF coaxial cable (supplied) to connect the OUT Jack on the Cable Box/DSS Receiver to the ANT(enna) IN Jack on the VCR.

3.Use a second RF coax- ial cable to connect the OUT Jack on the VCR to the TV’s ANTENNA IN

Jack.

ANTENNA IN Jack

Back of TV (example only)

Recording/Viewing Any Channel

1

With the VCR on and in VCR position (the VCR light will appear on the display panel), use the CH(annel) Up/Down buttons to set the VCR to the Cable Box/DSS Receiver output channel (channel 03 or 04).

2

Set the TV to the same channel to which you set the VCR.

3

Select the channel you want to watch or record at the Cable Box/DSS Receiver.

Watching TV With the VCR Off

1

Use the TV channel selector to set the TV to the Cable

Box/DSS Receiver output channel (channel 03 or 04).

2

Select the channel you want to watch at the Cable Box/DSS Receiver.

Timer Recordings

With this connection, you may set a timer recording as described on pages 34-37. However, you must remember the following:

●You can only program a timer recording for one channel at a time.

●Set the TV and the VCR to the Cable Box/DSS Receiver out- put channel (channel 03 or 04).

●When you are prompted to enter the channel you want to record, select channel 03 or 04 (the Cable Box/DSS Receiver output channel). (This is step 5 on page 35.)

●Set your Cable Box/DSS Receiver to the channel you want to record.

●Leave the Cable Box/DSS Receiver on while you are recording.

Helpful Hints

•With this hookup, channels cannot be changed at the VCR. You must select channels at the Cable Box/DSS Receiver.

•You can not view a channel other than the one you are recording (the instructions on page 32 do not work with this hookup).

•You cannot program channels with this hookup (as discussed on page 12).

•If you set up the VCR’s internal Cable Box Controller, the VCR will select the Cable Box channel auto- matically during a timer recording. You must place the Cable Box on top of the VCR. Details are on pages 38-39.

•Leave the Cable Box/DSS Receiver on while you are recording.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents VRX562AT Dear Philips Magnavox product owner For Customer UseIntroduction FeaturesSafety Precautions Table of Contents Putting Batteries in the Remote Control Using the Remote ControlVCR maintenance Erasure PreventionHookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d Plug in the TV and the VCRTimer Recordings Hookups With a Cable Box/DSS ReceiverRecording/Viewing Any Channel Watching TV With the VCR OffHookups With a Cable Box/DSS Receiver cont’d Recording One Channel/Watching AnotherPlaying a Tape Press the Play button to play the tapeHookups With a Stereo TV Turning on Your VCR 1Turn on the TVPress the Number 3 button to select Tuner SET UP Channel MemoryProgramming Channels Press the VCR buttonChannel Memory cont’d Adding/Deleting ChannelsReviewing Programmed Channels Use the Number buttons to enter the channel numberSetting the Clock Manual Clock SettingPress the Number 4 button to select SET Clock Press the Number 2 button to select SET Manual ClockSetting the Clock cont’d Setting the Clock cont’d Automatic Clock SettingPress the VCR button, then press the Menu button to Bring up the main menu displayTime Zone Press the Number 4 button to select SET Time ZoneDaylight-Saving Time Selection Daylight-Saving Time SelectionPress the Number 2 button to select VCR SET UP Language SelectionLanguage Selection Press the Number 4 button to select LanguagePress and release the Mute button 2Find your TV codeFind your Cable Box/Satellite 2System codeIf another remote control beeps Remote LocatorLetting your VCR find your remote for you Press the Mute button, then the PAUSE/STILL buttonCBL/DSS Button VCR ButtonTV Button Rewind ButtonRemote Control Buttons cont’d Slow Button Stop ButtonMenu Button Frame. ADVance ButtonPress the Number 2 button to select on Screen Mode On-Screen Status DisplaysTo choose the status display mode, follow the steps below PressedFeature Light Symbols VCR Display PanelFront Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape Press the VCR button on the remote control RecordingPress the Stop button to stop the recording Press the VCR button Start a recording seePress the TV button, then press the CHannel Up/Down One Touch Recording Timer Recording Press the Number 1 button to select ProgramDaily Recording MenuEnter the channel you want to record Enter the recording’s stop timeTape Speeds Timer Recording cont’dPress the STATUS/EXIT button. Program WAS COM See page 58 for more hints Checking or Cancelling Timer RecordingsMenu button Press the Number 1 button to select Program Find your Cable Box code Turn on the Cable Box Cable Box Cable Box Transmitters on VCRSetting Up the Cable Box Controller cont’d Local TV Stations Call letters Setting Up the VCR Plus+ Programming SystemTV Channels Cable Channels Examine the lists on Press the Number 5 button to select VCR PLUS+ REF. MAPOnce Complete each step within 60 seconds of completingPrevious step. If you don’t, you may return to step Press the VCR PLUS+ /ENTER button on the remote conTimer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication Repeat Playback Repeat PlaybackTime Search Time SearchIndex Search ExampleDuring tape playback press the Skip Search button Record End SearchSkip Search Real Time Counter Memory Real Time Counter MemorySpecial Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Playing a Tape at Double SpeedPress the Play button to release the Still mode Viewing a Slow Motion PictureViewing a Picture in Slow to Fast Motion Play button or press the Slow button againAutomatic Operation Features Memory Rewind, Power OffAutomatic Playback Automatic Rewind, Eject, OffManual Tracking Automatic Operation Features cont’dAutomatic Tracking Adjustment MTS Broadcast Stereo System Understanding On-Screen DisplaysSpecifically… MonitorMTS Broadcast Stereo System cont’d To the right of your selectionAdditional hints are on Hi-Fi Stereo Sound SystemPress the Number 3 button to select Audio OUT Hi-Fi Stereo Sound System cont’d Helpful Hints Helpful Hints cont’d Glossary Cable Box/DSS Receiver Output Channel Channel 03 orSpecifications Renewed Index Supplied Accessories
Top Page Image Contents