Magnavox VRX562AT99 warranty Time Search

Page 46

46 Time Search

Time Search

Follow the steps below to program the VCR to search forward or backward a specific length of time.

1

Press the VCR button.

2

Press the TIME SEARCH button to bring up the time search display. There must be a tape in the VCR.

TIME SEARCH

0:00

ENTER SEARCH TIME

3

Within 10 seconds, use the Number buttons to enter the desired length of time you want to skip forward or back- ward. For example, for 1 hour, 25 minutes, press Number but- tons 1, 2, 5. Or, for five minutes, press Number buttons 0, 0, 5. (Make an entry within 10 seconds of pressing the TIME SEARCH button. Otherwise, the VCR will exit Time Search mode.)

4

Within 10 seconds, press the Fast Forward button or the Rewind button to skip forward or backward. The VCR will skip over the specified length of time, then begin playback. (The time counts down on-screen as the searching progresses.)

		1
	CBL/DSS		VCR	TV
	PAUSE	POWER		VCR PLUS+
4	/STILL			/ENTER
	/STILL
	SLOW			F.ADV
	STATUS/EXIT			CLEAR
		MENU
	V			C
		VOL	CH
	V			C
3	1		2	3
3	4		5	6
	4		5	6
	7		8	9
	100		0	A.CH
	REC/OTR	INDEX	SKIP
	REC/OTR	SEARCH	SEARCH	VCR/TV
	SPEED	MEMORY
2	EJECT	X2 PLAY	VAR.SLOW	TRACKING
2	MUTE		TIME SEARCH REC END SEARCH

JOG & SHUTTLE

Helpful Hints

•If you want to search for more than 59 minutes, you must enter the length of time in hours and minutes. For example, to search forward 70 minutes, press 1,1,0 at step 3.

•You can not enter the TIME SEARCH menu when you are in Recording mode.

•You can remove the Time Search display by pressing the TIME SEARCH button again.

•To cancel the Time Search when the VCR is fast forwarding or rewinding, press the STOP button once or the TIME SEARCH button twice.

Image 46

Contents VRX562AT Dear Philips Magnavox product owner For Customer UseSafety Precautions FeaturesIntroduction Table of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Erasure PreventionHookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d Plug in the TV and the VCRRecording/Viewing Any Channel Timer RecordingsHookups With a Cable Box/DSS Receiver Watching TV With the VCR OffPlaying a Tape Hookups With a Cable Box/DSS Receiver cont’dRecording One Channel/Watching Another Press the Play button to play the tapeHookups With a Stereo TV Turning on Your VCR 1Turn on the TVProgramming Channels Press the Number 3 button to select Tuner SET UPChannel Memory Press the VCR buttonReviewing Programmed Channels Channel Memory cont’dAdding/Deleting Channels Use the Number buttons to enter the channel numberPress the Number 4 button to select SET Clock Setting the ClockManual Clock Setting Press the Number 2 button to select SET Manual ClockSetting the Clock cont’d Press the VCR button, then press the Menu button to Setting the Clock cont’dAutomatic Clock Setting Bring up the main menu displayTime Zone Press the Number 4 button to select SET Time ZoneDaylight-Saving Time Selection Daylight-Saving Time SelectionLanguage Selection Press the Number 2 button to select VCR SET UPLanguage Selection Press the Number 4 button to select LanguagePress and release the Mute button 2Find your TV codeFind your Cable Box/Satellite 2System codeLetting your VCR find your remote for you If another remote control beepsRemote Locator Press the Mute button, then the PAUSE/STILL buttonTV Button CBL/DSS ButtonVCR Button Rewind ButtonRemote Control Buttons cont’d Menu Button Slow ButtonStop Button Frame. ADVance ButtonTo choose the status display mode, follow the steps below Press the Number 2 button to select on Screen ModeOn-Screen Status Displays PressedFeature Light Symbols VCR Display PanelFront Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR Press the VCR button on the remote control RecordingPress the TV button, then press the CHannel Up/Down Press the VCR button Start a recording seePress the Stop button to stop the recording One Touch Recording Daily Timer RecordingPress the Number 1 button to select Program Recording MenuEnter the channel you want to record Enter the recording’s stop timePress the STATUS/EXIT button. Program WAS COM Timer Recording cont’dTape Speeds Menu button Press the Number 1 button to select Program Checking or Cancelling Timer RecordingsSee page 58 for more hints Find your Cable Box code Turn on the Cable Box Cable Box Cable Box Transmitters on VCRSetting Up the Cable Box Controller cont’d TV Channels Cable Channels Setting Up the VCR Plus+ Programming SystemLocal TV Stations Call letters Examine the lists on Press the Number 5 button to select VCR PLUS+ REF. MAPPrevious step. If you don’t, you may return to step OnceComplete each step within 60 seconds of completing Press the VCR PLUS+ /ENTER button on the remote conTimer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication Repeat Playback Repeat PlaybackTime Search Time SearchIndex Search ExampleSkip Search Record End SearchDuring tape playback press the Skip Search button Real Time Counter Memory Real Time Counter MemorySuper High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Playing a Tape at Double SpeedViewing a Picture in Slow to Fast Motion Press the Play button to release the Still modeViewing a Slow Motion Picture Play button or press the Slow button againAutomatic Playback Automatic Operation FeaturesMemory Rewind, Power Off Automatic Rewind, Eject, OffAutomatic Tracking Adjustment Automatic Operation Features cont’dManual Tracking Specifically… MTS Broadcast Stereo SystemUnderstanding On-Screen Displays MonitorMTS Broadcast Stereo System cont’d To the right of your selectionPress the Number 3 button to select Audio OUT Hi-Fi Stereo Sound SystemAdditional hints are on Hi-Fi Stereo Sound System cont’d Helpful Hints Helpful Hints cont’d Glossary Cable Box/DSS Receiver Output Channel Channel 03 orSpecifications Renewed Index Supplied Accessories