FUNAI LC200EM8G owner manual 5Troubleshooting Guide

Page 25

TROUBLESHOOTING

5Troubleshooting Guide

If the unit does not perform properly when operated as instructed in this owner's manual, check the following chart once before calling for service.

Symptom	Remedy
No power	• Be sure the power cord is plugged in.
	• If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to
	reset itself.
No picture or sound	• Check if the power is on.
	• Check the outlet connection.
	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
	• Turn off the power and wait for about 1 minute, then turn it on again.
No color	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
	• Adjust the “COLOR” in the main menu.
Sound OK, picture poor	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• Adjust “CONTRAST” and “BRIGHTNESS” in the main menu.
	• View other TV channels. The problem might be limited to the broadcasting station.
Picture distorted	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
Weak picture	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• Adjust “CONTRAST” and “BRIGHTNESS” in the main menu.
	• View other TV channels. The problem might be limited to the broadcasting station.
Lines or streaks in picture	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Picture blurred	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
Ghosts in picture	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Bars on TV screen	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
Picture rolls vertically	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Different color marks on TV	• Move the unit away from nearby electric appliances. Turn off the power and wait
screen	30 minutes before turning it back on.
	• View other TV channels. The problem might be limited to the broadcasting station.
Poor reception on some	• Check the antenna or cable connection to the main unit.
channels	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Picture OK, sound poor	• View other TV channels. The problem might be limited to the broadcasting station.

No reception of digital signals	• Make sure auto channel scan has been completed. (Refer to “Auto Channel Scan”
	on page 12.)
	Auto channel scan must be completed when you set up the unit for the first time
	or move it to a location where previously unavailable channels are broadcast.
	• The selected channel may not be broadcasting.
	• When auto channel scan is interrupted and not completed, some channels will not
	be received. Make sure to complete. (Refer to “Auto Channel Scan” on page 12.)

INTRODUCTION CONNECTION INITIAL SETTING WATCHING TV OPTIONAL SETTING TROUBLESHOOTING INFORMATION

25

EN

Image 25

Contents LC200EM8G To Receive DIGITAL/ANALOG SIGNAL, YOU Must Connect AntennaImportant note is located on the rear of the cabinet IntroductionRADIO-TV Interference Precautions5Symbols Used in this Manual 5Supplied Accessories5Tilt Stand LocationContents Features5Installing the Batteries 5Remote Control Function5Rear Panel 5Control Panel5Basic Connection ConnectionAntenna Cable Connection Connection to Cable Box or Satellite BoxComponent Video Cable Connection 5External Device ConnectionVideo Cable Connection Video Connection RCA video cable5Initial Setup Initial Setting5Main Menu 5Language Selection 5Auto Channel ScanWatching TV What is the minor channel?5Channel Selection Use CH. K/L or the Number buttons5Switching Audio Mode 5Switching Each ModeMain SAPPress Display 5Screen InformationBroadcasting Information Program Guide5Sleep Timer 5TV Screen Display ModeTo Cancel the Sleep Timer Letterbox5Channel Add/Delete Optional Setting5Closed Caption 5Picture AdjustmentBrightness Contrast Tint SharpnessPress Enter repeatedly to change the setting To select Caption SERVICE, thenTo select DTVCC, then press Enter5DTVCC Style 5Color Temperature 5Back Light SettingYou can set the desired brightness mode You can adjust color temperature of the TV screenCertain programming inappropriate for children 5V-chipTo Set the Sub Ratings Change the settingAssociation of America To select Mpaa RATING, then pressEnter password again in Confirm Password space Change Password5Troubleshooting Guide TroubleshootingControl’s infrared signal MaintenanceWith an AM radio Phone camerasInformation Limited Warranty