Panasonic AK-HRP931P Gain Phase, Head OPT Level, CCU OPT Level, HCO Hfin Sdtv, Scco Scfin Sdtv

Page 11

Parts and their functions

+CLP: Detail edge overshoot clip

This is used to limit the length of the overshoot parts of the detail edge components.

–CLP: Detail edge undershoot clip

This is used to limit the length of the undershoot parts of the detail edge components.

KNEE: Detail edge knee

This function applies the knee to the detail edge parts.

CRM: Chroma detail

This function boosts the detail in the high chroma saturation.

CRSP: Chroma detail crisp

This is used to remove the very faint noise components below the level set from the chroma detail components.

CRED: Chroma detail reduce

This is used to suppress the chroma detail edge.

SKIN_DTL: Skin tone detail

This is used to set the skin tone detail function to ON or OFF.

SKIN_LVL: Skin tone detail level

This is used to set the chroma saturation of the parts where the skin tone detail is applied.

ZEB: Skin tone area zebra

This is used to set whether or not to apply zebra to the areas where coring is applied as the skin tones to the Y signals in the PM output.

PHAS: Skin tone area phase

This is used to move the areas recognized as the skin tones in the range of 153 to 93 along the Q axis on the color vector display.

WIDTH: Skin tone area width

This is used to widen the areas recognized as the skin tones in the range of 1 to 20 along the I axis on the color vector display.

CRSP: Skin tone detail crisp

This is used to remove the very faint noise components below the level set from the skin tone detail components.

>Matrix control switch [MATRIX CONTROL]

This is pressed to change the correction amounts for the R-G, R-B, G-R, G-B, B-R and B-G chroma saturation.

R-G R-B G-R

G-B

–10

0

+1

+10

B-R

B-G

 

 

0

0

 

 

MTX 12

 

GAIN

PHASE

Cy_B

 

0

0

MTX 12, GAIN, PHASE

These are used to select the following 12-axis matrix adjustment items: G, G_Cy, Cy, Cy_B, B, B_Mg, Mg, Mg_R, R, R_Ye, Ye and Ye_G.

GAIN

This is used to adjust the chroma saturation (gain) of the items set using MTX 12 in the range of –127 to +127.

PHASE

This is used to adjust the phase of the items set using MTX 12 in the range of –127 to +127.

?SYSTEM

 

HEAD OPT LEVEL

πππππ

CCU OPT LEVEL

πππππ

RET1 RET2 RET3 RET4

HDSDI1 HDSDI2 HDSDI3 HDSDI4

DCMD

UCMD

DCLK

UCLK

SP

SP

ON

ON

HBAR

SBAR

PATHO

SET

ARIB

SMPT

OFF

7.5%

SDI4

 

MSEL

MLINK

PM

 

MIX

ON

ANLG

O_SEL SYNC TYPE

SD

RGB

ON

TRI

H_CO

HFIN

(HDTV)

 

99

123

 

 

H_CO

HFIN

(SDTV)

 

99

123

 

 

SCCO

SCFIN

(SDTV)

 

730 SH_H SH_V 0 90H

VER

HEAD, CCU OPT LEVEL:Camera, CCU light reception strength level

These indicate the light reception strength margins of the camera head and CCU.

RET1, RET2, RET3, RET4: Return video settings

These are used to set the input allocations of the return signals.

DCMD: Down-conversion system selection

This is used to select the down-conversion system.

UCMD: Up-conversion system selection

This is used to select the up-conversion system.

11

Image 11
Contents AK-HRP931P FCC Note Safety precautionsOverview ContentsAccessories Operating precautions Parts and their functions = Mode ON/OFF switches PM character display switch CharacterCPU reset switch RST Vertical frequency status indicator 60Hz100 -49 0 +7 Adjustment item up and down shift switches 3? Control item selector switches Hsaw Hpar Vsaw VparBlkr Blkm Blkb Rpnt Mpnt BpntRslp Mslp Bslp ClipVdtl Hdtl Crsp Peak LDP Dark Rflr Gflr BflrRgam Ggam Bgam Rgan Ggan BganLDP Dark 10% Vdtl Hdtl Crsp PEAK1 PEAK2HCO Hfin Sdtv Gain PhaseHead OPT Level CCU OPT LevelALC Sped @ LCD display Adjustment rotary encodersMonitor selector switches Master pedestal active switch M-PED Active Iris joystick control range selector switch FullAuto iris switch Auto Iris active switch Iris ActiveConnections CCU connectorRCP connector Preview control connector PreviewSpecifications External dimension drawingsVQT0A41