Aiwa VX-S205U, VX-S135U manual Qildoor Antenna, Lightning, ~&ntenancx3, Damaae Reauirirwt Service

Power-cod Protection. The unit is provided with an attachment plug with overload protection. This IS a safety feature. See operating instructions for replacement or resetting of protective device. If replacement of the plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug.

CXmrloacting - Do not alk~w anything to rest on the power cord. Do not overload wall outlets and extension cords because this can result in fire or electric shock. Do not place the unit in an area where people will walk on the cord.

Qildoor Antenna

Power lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall onto such power lines or circuits. When installing an outside antenna system, extreme care should be taken to avoid touching power lines or circuits because contact with them may be fatal.

outdoor Antenna Grounding - [f an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANS1/ NFPA No.70, provides information with regard to proper grounding of the mast anl~ supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, locatlon of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See the figure.

Antenna Grounding Acc xdlng to the National Electrical Cord

H , ANTENNA LEAD IN WIRE

/’	GROUND CLAI’
=
ELECTRIC
SERVICE
EQUIPMENT		)
T=
“’---d	1~~	GROUND CLAMPS
		(NEC ART 250 PART H)

NEC-NATIONAL ELECTRICAL (: ODE

Lightning

For added protection during a lightning storm, or when left uni~ttended and unused for long periods of time, unplug the unit from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and powerlme surges.

~&ntenancx3

Cleaning - Unplug the unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Damaae Reauirirwt Service

Unplug the unit from the wail outlet and refer servicing to qualified service personnel under the following conditions:

1)When the power cord or plug is damaged or frayed.

2)If liquid has been spilled into the unit.

3)If the unit has been exposed to rain or water.

4)If the unit does not operate normally when following the operating instructions. Adjust only those controls that are covered by the operating instructions because Improper adjustment of other controls may result in damage to the unit and will often require extensive work by a qualified technician to restore the unit to normal operation.

5)If the unit has been dropped or the cabinet has been damaged.

6)When the unit exhibits a distinct change in performance - this indicates a need for service.

Do not attempt to service the unit yourself because opening or removing covers may expose you to high voltage or other hazards. Refer all servicing to qualified service personnel.

Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or having the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

Safety Check - After completion of any service or repairs to the unit, ask the service technician to perform a safety check to ensure that the unit is in proper operating condition.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NIEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the building, as close to the point of cable entry as practical.

OVUNER’SRECORD

For your convenience, record the model number and serial number (you will find them on the rear of your set) in the space provided below. Please refer to them when you contact your AIWA dealer in case of difficulty.

Model No.

[~—_–.]

Serial No. ‘–”---1

ENGLISH 2