Tandberg Data LTO-1 HH, LTO-3 HH, LTO-2 HH Scsi Bus Interface, Scsi Controller Board Installation

Page 11

Tandberg Data

Tape Drive Installation

 

 

 

Do not use longer screws or higher screw torquethan specified!

Longer screws will bottom and not fasten the drive!

Safe penetration of mounting

screws: min 2 mm, max 2.5 mm

Wall of server chassis

Tape drive's

mounting screwTape drive's casting

Figure 3.3 Mounting screw details

3.6 SCSI Bus Interface

The Tandberg LTO HH tape drive is designed to operate on an Ultra160 low voltage differential SCSI bus (LVD) with a burst transfer rate up to 160 MB/sec. The Ultra160 SCSI interface is backward compatible with older SCSI interfaces. Thus all Ultra Wide may be used.

The tape drive features a high density 68-pin (HD-68) connector for attachment to the server or to the interface connector in an external tabletop cabinet.

Attachment to the host computer is described below.

3.7 SCSI Controller Board Installation

Note:

Before any SCSI device can be installed it is necessary to have a SCSI controller board installed. Please pay attention to the following points.

Make sure your computer is turn off before proceeding to the installation.

If you computer is equipped with an onboard SCSI controller, before proceeding with the installation, you must first locate the SCSI connector on the computer motherboard.

Tandberg LTO HH Installation and User Manual

7

Image 11
Contents Tandberg LTO HH Trademarks Change logTable of Contents Tandberg Data Contents Introduction Features and BenefitsTandberg Data Introduction How to Contact Tandberg Data Technical SupportPower Requirements SpecificationsMedia Specifications and Compatibility Mechanical DimensionsData Compression Heat DissipationTape Backup Software Installation Tape Drive InstallationSolution Contents Allowed mounting orientations Mounting Screw RequirementsScsi Bus Interface Scsi Controller Board InstallationSCSI-ID Selection Tandberg LTO HH Internal Tape Drive Scsi ConfigurationTermination in General SCSI-bus TerminationSCSI-ID Selection Tandberg LTO HH External Tape Drive SCSI-bus Termination External Tape Drives SCSI-bus Termination Internal Tape DrivesExternal Tape Drive Installation Installation Internal Tape DriveVerifying Tape Drive Operation 10 Connecting the external Tandberg LTO HH tape driveTape Cartridge Operation Front LED IndicatorsTape Drive Operation Loading a Data Cartridge Into a Tandberg LTO HH Write Protecting the CartridgeEjecting a Data Cartridge From a Tandberg LTO HH Cleaning the Tape DriveRecommended Cleaning Interval Cleaning ProcedureStoring LTO Cartridges Cleaning Cartridge ReplacementHandling and Storing LTO Cartridges Handling LTO CartridgesWindows 2000/2003/XP Software InstallationWindows Tape Driver Windows Tape Driver Installation Windows Embedded Backup ApplicationHost Adapter SCO Open Server System CommandsTar command examples SCO Open ServerSCO UnixWare SCO Open Server Backup ManagerInstallation SCO UnixWare System CommandSun Solaris Tape Drive InstallationSun System Command IBM AIX Storage Manager IBM AIX System CommandHP/UX 2 HP/UX System CommandScsi Host Adapter Linux System CommandLinux Tape Drive Utilities FlashIt Firmware Upgrade UtilityTDkit Tool for Testing and Downloading Firmware Software Checking TroubleshootingStandalone Diagnostics Hardware CheckingFailure Indication Starting the TestTest Sequence Degraded Media Cleaning is requiredMedia Management Reporting Damaged Front Bezel Problem SituationsDead on Arrival Noisy Tape Drive Drive Not Detected by the Operating System OSWill Not Insert/Hold Media /Media is Not Recognized Cartridge is Stuck Inside the Drive Fault LED Flashes Amber and the Activity LED is OffIntermittent Failures Cleaning LED Is onIncorrect Data Compression Slow PerformanceIf the error occurs always on the same file or directory Tape Removal ProcedureIf the problem occurs in the middle of an operation Glossary of Terms Ultra/Ultra2 ScamLED-behavior During Normal Operation App. A. LED-Indicator BehaviorTandberg Data LED Bahavious

LTO-1 HH, LTO-2 HH, LTO-3 HH specifications

Tandberg Data has long been recognized as a leading provider of innovative data storage and backup solutions, and their tape drives, specifically the LTO-1, LTO-2, and LTO-3 Half Height (HH) models, represent a significant advancement in data storage technology. These systems are designed to meet the demands of modern data management, balancing capacity, speed, and reliability.

The LTO-1 HH, introduced in 2001, marked a groundbreaking step in the linear tape-open (LTO) technology. It offered a native storage capacity of 100 GB and a compressed capacity of up to 200 GB. The tape drive featured a data transfer rate of 20 MB/s, allowing for efficient backup processes. One of the key technologies in the LTO-1 was its use of ultral Linear Tapes, which helped in maintaining the integrity of data over extended periods. The built-in data compression capabilities also contributed to the efficient storage of large volumes of data, making it suitable for small to medium-sized businesses.

Building on the success of the LTO-1, the LTO-2 HH was launched, significantly enhancing performance with a native capacity of 200 GB and a compressed capacity of up to 400 GB. The data transfer rate improved as well, reaching 40 MB/s. The LTO-2 introduced the concept of WORM (Write Once, Read Many) technology, which added a layer of security by ensuring that data could not be tampered with after being written. This was particularly important for industries requiring regulatory compliance. Enhanced error correction and data integrity features were also hallmarks of the LTO-2, ensuring reliable long-term data storage.

The LTO-3 HH followed suit with even greater advancements, providing a native capacity of 400 GB and a compressed capacity of 800 GB, along with a data transfer rate of up to 80 MB/s. Its improved track layout and data encoding methods further enhanced performance and reliability. Additionally, LTO-3 introduced the partitioning feature, which divided the tape into virtual partitions for more efficient data management, allowing users to access data faster. The data encryption capabilities introduced with LTO-3 provided enhanced security, protecting sensitive data during backup and storage.

Together, these Tandberg Data LTO tape drives showcase a remarkable evolution in data storage technology, offering robust solutions that cater to businesses of all sizes. Their reliability, security features, and substantial data capacities ensure that organizations can efficiently manage their growing data storage needs in an increasingly digital world.