Noisy Tape Drive | Tandberg Data LTO-3 HH, LTO-2 HH, LTO-1 HH

Tandberg Data	Troubleshooting

2.Remove the damaged front bezel.

Use a small flat screwdriver or your fingernails to lift the small plastic “ears” on each side of the drive.

3.Install the new bezel.

Push it gently onto the front of the drive until the “ears” snap into place on each side.

6.6.3 Drive Not Detected by the Operating System (OS)

1.Check LED activity at Power Up

All four LEDs flash for two seconds at power up and the Ready LED flashes for several seconds while the power-on self test is running.

2.Check the SCSI-ID

Each device on the SCSI bus needs a unique SCSI-ID. The SCSI-ID is set with jumpers on the backside of the drive. See label on drive, the installation guide supplied with the tape drive, or on the web for instructions.

3.Check SCSI termination

The SCSI bus should be terminated at the end of the cable; a defective terminator may leave the drive in a reset condition.

6.6.4 Will Not Insert/Hold Media /Media is Not Recognized

1.Check cartridge type.

Tandberg LTO-3 HH will only accept LTO-1, LTO-2 or LTO-3 type data or cleaning cartridges. Tandberg LTO-2 HH will only accept LTO-1 or LTO-2 type data or cleaning cartridges. Tandberg LTO-1 HH will only accept LTO-1 or cleaning cartridges.

If a wrong type of cartridge is inserted, it can be mechanically prevented from being inserted or electrically rejected after insertion.

2.Check media orientation.

The arrow on the cartridge must point into the tape drive facing up when the tape drive is mounted horizontally with the LEDs on the right.

Media can be inserted only the “correct way”; there are mechanical blockings if the media is insert wrong.

3.Try using a new cartridge.

If it loads correctly, check the failing cartridge for damage.

4.Check failing media for pin damage (buckling pin).

Hold the cartridge in your hand with the Write Protect Switch to your left and orientation arrow pointing from you. On the right side all the way in front is a small door that can be opened by sliding a door against you. Inside the cartridge you should see a metal pin, the pin shall be parallel with the cartridge front and is hold in place by to metal grippers at each end (top and bottom of the cartridge). The media should be attached to this pin, and you see only the top and bottom part of the pin.

If the pin is missing, loose or damaged the tape will be damaged and rejected from the drive.

6.6.5 Noisy Tape Drive

There are no fans in the Tandberg LTO HH tape drive and the noise should be very low in idle mode. When the tape moves the noise can come from the media itself. The drive will give a steady sound when streaming. The sound is “intermittent” if the host is not delivering data at the data rate of the drive.

1.Check if the noise comes from the cartridge.

Insert new media – first check this media for any damage.

Tandberg LTO HH Installation and User Manual

LTO-1 HH, LTO-2 HH, LTO-3 HH specifications

Tandberg Data has long been recognized as a leading provider of innovative data storage and backup solutions, and their tape drives, specifically the LTO-1, LTO-2, and LTO-3 Half Height (HH) models, represent a significant advancement in data storage technology. These systems are designed to meet the demands of modern data management, balancing capacity, speed, and reliability.

The LTO-1 HH, introduced in 2001, marked a groundbreaking step in the linear tape-open (LTO) technology. It offered a native storage capacity of 100 GB and a compressed capacity of up to 200 GB. The tape drive featured a data transfer rate of 20 MB/s, allowing for efficient backup processes. One of the key technologies in the LTO-1 was its use of ultral Linear Tapes, which helped in maintaining the integrity of data over extended periods. The built-in data compression capabilities also contributed to the efficient storage of large volumes of data, making it suitable for small to medium-sized businesses.

Building on the success of the LTO-1, the LTO-2 HH was launched, significantly enhancing performance with a native capacity of 200 GB and a compressed capacity of up to 400 GB. The data transfer rate improved as well, reaching 40 MB/s. The LTO-2 introduced the concept of WORM (Write Once, Read Many) technology, which added a layer of security by ensuring that data could not be tampered with after being written. This was particularly important for industries requiring regulatory compliance. Enhanced error correction and data integrity features were also hallmarks of the LTO-2, ensuring reliable long-term data storage.

The LTO-3 HH followed suit with even greater advancements, providing a native capacity of 400 GB and a compressed capacity of 800 GB, along with a data transfer rate of up to 80 MB/s. Its improved track layout and data encoding methods further enhanced performance and reliability. Additionally, LTO-3 introduced the partitioning feature, which divided the tape into virtual partitions for more efficient data management, allowing users to access data faster. The data encryption capabilities introduced with LTO-3 provided enhanced security, protecting sensitive data during backup and storage.

Together, these Tandberg Data LTO tape drives showcase a remarkable evolution in data storage technology, offering robust solutions that cater to businesses of all sizes. Their reliability, security features, and substantial data capacities ensure that organizations can efficiently manage their growing data storage needs in an increasingly digital world.