Tandberg Data LTO-2 HH, LTO-3 HH Mounting Screw Requirements, Allowed mounting orientations

Page 10

Tandberg Data

Tape Drive Installation

 

 

 

3.3 Installation of Software Device Drivers

If the backup application software does not detect the tape drive, or obtain the latest operating system drivers and upgrades, please visit www.tandbergdata.com.

3.4 Mechanical Installation Internal Tape Drive

For mechanical mounting specifications, see Figure 3.2.

Allowed mounting position is either horizontal with the indicator LEDs to the right, or vertical with the indicator LEDs up (see Figure 3.1).

Figure 3.1 Allowed mounting orientations

The drive occupies a half-height 5.25-inch slot with mounting screws on both sides of the drive chassis or at the bottom of the drive.

Figure 3.2 Mounting specifications

3.5 Mounting Screw Requirements

Only M3 (metric) screws must be used for mounting the drive

Maximum permitted screw penetration:

2.5 mm

Minimum required screw penetration:

2.0 mm

Screw torque, mounting screws:

0.5 Nm

Screws are supplied with all the Tandberg LTO HH drive variants

• Bag with 4 screws and 4 SCSI-ID jumpers (Ordering no. 43 32 65)

6

Tandberg LTO HH Installation and User Manual

Image 10
Contents Tandberg LTO HH Change log TrademarksTable of Contents Tandberg Data Contents Features and Benefits IntroductionHow to Contact Tandberg Data Technical Support Tandberg Data IntroductionMechanical Dimensions SpecificationsMedia Specifications and Compatibility Power RequirementsHeat Dissipation Data CompressionSolution Contents Tape Drive InstallationTape Backup Software Installation Mounting Screw Requirements Allowed mounting orientationsScsi Controller Board Installation Scsi Bus InterfaceScsi Configuration SCSI-ID Selection Tandberg LTO HH Internal Tape DriveSCSI-ID Selection Tandberg LTO HH External Tape Drive SCSI-bus TerminationTermination in General SCSI-bus Termination Internal Tape Drives SCSI-bus Termination External Tape DrivesInstallation Internal Tape Drive External Tape Drive Installation10 Connecting the external Tandberg LTO HH tape drive Verifying Tape Drive OperationTape Drive Operation Front LED IndicatorsTape Cartridge Operation Write Protecting the Cartridge Loading a Data Cartridge Into a Tandberg LTO HHCleaning Procedure Cleaning the Tape DriveRecommended Cleaning Interval Ejecting a Data Cartridge From a Tandberg LTO HHHandling LTO Cartridges Cleaning Cartridge ReplacementHandling and Storing LTO Cartridges Storing LTO CartridgesWindows Embedded Backup Application Software InstallationWindows Tape Driver Windows Tape Driver Installation Windows 2000/2003/XPSCO Open Server SCO Open Server System CommandsTar command examples Host AdapterSCO UnixWare System Command SCO Open Server Backup ManagerInstallation SCO UnixWareSun System Command Tape Drive InstallationSun Solaris IBM AIX System Command IBM AIX Storage Manager2 HP/UX System Command HP/UXLinux Linux System CommandScsi Host Adapter TDkit Tool for Testing and Downloading Firmware FlashIt Firmware Upgrade UtilityTape Drive Utilities Hardware Checking TroubleshootingStandalone Diagnostics Software CheckingTest Sequence Starting the TestFailure Indication Media Management Reporting Cleaning is requiredDegraded Media Dead on Arrival Problem SituationsDamaged Front Bezel Will Not Insert/Hold Media /Media is Not Recognized Drive Not Detected by the Operating System OSNoisy Tape Drive Fault LED Flashes Amber and the Activity LED is Off Cartridge is Stuck Inside the DriveSlow Performance Cleaning LED Is onIncorrect Data Compression Intermittent FailuresIf the problem occurs in the middle of an operation Tape Removal ProcedureIf the error occurs always on the same file or directory Glossary of Terms Scam Ultra/Ultra2App. A. LED-Indicator Behavior LED-behavior During Normal OperationTandberg Data LED Bahavious

LTO-1 HH, LTO-2 HH, LTO-3 HH specifications

Tandberg Data has long been recognized as a leading provider of innovative data storage and backup solutions, and their tape drives, specifically the LTO-1, LTO-2, and LTO-3 Half Height (HH) models, represent a significant advancement in data storage technology. These systems are designed to meet the demands of modern data management, balancing capacity, speed, and reliability.

The LTO-1 HH, introduced in 2001, marked a groundbreaking step in the linear tape-open (LTO) technology. It offered a native storage capacity of 100 GB and a compressed capacity of up to 200 GB. The tape drive featured a data transfer rate of 20 MB/s, allowing for efficient backup processes. One of the key technologies in the LTO-1 was its use of ultral Linear Tapes, which helped in maintaining the integrity of data over extended periods. The built-in data compression capabilities also contributed to the efficient storage of large volumes of data, making it suitable for small to medium-sized businesses.

Building on the success of the LTO-1, the LTO-2 HH was launched, significantly enhancing performance with a native capacity of 200 GB and a compressed capacity of up to 400 GB. The data transfer rate improved as well, reaching 40 MB/s. The LTO-2 introduced the concept of WORM (Write Once, Read Many) technology, which added a layer of security by ensuring that data could not be tampered with after being written. This was particularly important for industries requiring regulatory compliance. Enhanced error correction and data integrity features were also hallmarks of the LTO-2, ensuring reliable long-term data storage.

The LTO-3 HH followed suit with even greater advancements, providing a native capacity of 400 GB and a compressed capacity of 800 GB, along with a data transfer rate of up to 80 MB/s. Its improved track layout and data encoding methods further enhanced performance and reliability. Additionally, LTO-3 introduced the partitioning feature, which divided the tape into virtual partitions for more efficient data management, allowing users to access data faster. The data encryption capabilities introduced with LTO-3 provided enhanced security, protecting sensitive data during backup and storage.

Together, these Tandberg Data LTO tape drives showcase a remarkable evolution in data storage technology, offering robust solutions that cater to businesses of all sizes. Their reliability, security features, and substantial data capacities ensure that organizations can efficiently manage their growing data storage needs in an increasingly digital world.