Pioneer VSX-1018AH-K manual Other Settings Chapter, Input Setup menu

Other Settings

Chapter 10:

Other Settings

The Input Setup menu

You only need to make settings in the Input Setup menu if you didn’t hook up your digital equipment according to the default settings (see Input function default and possible settings on page 68). In this case, you need to tell the receiver what equipment is hooked up to which terminal so the buttons on the remote correspond to the components you’ve connected.

				PARAMETER		PARAMETER
				EXIT	TUNE	TOOLS	MEM
RECEIVER			SOURCE	TOP MENU		AUDIO DISPLAY	CH
						MENU
						T.EDIT
					ENTER	TV CTRL	RECEIVER
DVD	BD	TV	HDMI	ST		ST
DVR 1	DVR 2	CD	CD-R	CATEGORY		RETURN
FM/AM	XM	SIRIUS	iPod USB	SETUP	TUNE	MAIN	ZONE 2
				iPod CTRL

1Switch on the receiver and your TV. Use the  RECEIVER button to switch on.

2Press RECEIVER on the remote control, then press

SETUP.

An on-screen display (OSD) appears on your TV. Use / // and ENTER to navigate through the screens and select menu items. Press RETURN to confirm and exit the current menu.

3Select ‘Input Setup’ from the System Setup menu.

System Setup MENU					6.Input Setup		(1/2)
1		. Auto	MCACC		Input
							DVD
2		. Surround Back System			Digital In	[	COAX-1	]
3		. Manual MCACC			HDMI Input	[	Input-1	]
4		. Data	Management		Component In [		Comp-3	]
5		. Manual SP Setup
	6	. Input	Setup
	7	. Other	Setup
			:Exit	(		NEXT	)
							:Finish

4Select the input function that you want to set up. The default names correspond with the names next to the terminals on the rear panel (such as DVD or VIDEO) which, in turn, correspond with the names on the remote control.

6.Input Setup		(1/2)		6.Input	Setup	(1/2)
Input					( Back	)
		DVD
Digital In	[	COAX-1	]		DVD
HDMI Input	[	Input-1	]	Input	Name	Rename
Component In [		Comp-3	]	PDP	In (SR+) [	OFF	]
(	NEXT	)
		:Finish		ENTER:Next		:Finish

10

5Select the input(s) to which you’ve connected your component.

For example, if your DVD player only has an optical output, you will need to change the DVD input function’s Digital In setting from COAX-1(default) to the optical input you’ve connected it to. The numbering (OPT-1and 2) corresponds with the numbers beside the inputs on the back of the receiver.

•If you change the setting to an input that has been previously assigned to another function (for example, TV SAT), the setting for that function will automatically be switched off.

•If your component is connected via a component video cable to an input terminal other than the default, you must tell the receiver which input terminal your component is connected to, or else you may see the composite video signals instead of the component video signals.1

6When you’re finished, select ‘Next’ to continue to the next screen.

The second screen of the Input Setup has three optional settings:

•Input Name – You can choose to rename the input function for easier identification. Select Rename to do so, or Default to return to the system default.

•PDP In (SR+) – To control certain functions on this receiver from a flat panel TV, select the display input to which you’ve connected the receiver.2

7When you’re finished, press RETURN.

You will return to the System Setup menu.

Note

1For high-definition video (using component video connections), or when digital video conversion is switched off (in Setting the Video options on page 72), you must connect your TV to this receiver using the same type of video cable as you used to connect your video component.

2You will have to make an SR+ cable connection from a CONTROL OUT jack on the display to the CONTROL IN jack on this receiver (opposite from the setup in Using this receiver with a Pioneer flat panel TV on page 63). Note that to control this receiver using the remote, you will have to point it at the flat panel TV’s remote sensor after making this connection.

67

En