Pioneer VSX-1018AH-K Using Acoustic Calibration EQ Professional, Select an option and press Enter

The System Setup menu 07

•Reverb characteristics for different channels – Reverb characteristics can be somewhat different for each channel. Since this difference increases as the sound is influenced by the various room characteristics, it is often better to capture a frequency analysis early on for smoother mixing of channel frequencies/sounds.

Level		Left
		surround
		Right
		surround
	Acoustic Cal. EQ Pro.	Conventional MCACC
	calibration range
		EQ calibration range
			Time
0	80	160 (in msec)

If your room isn’t affected by the factors above, it is often not necessary to make a 30~50ms setting. Later time settings may provide a more detailed sound experience with your speaker system. It is best to try and see what works best for your particular room.

Note that changing the room (for example, moving furniture or paintings) will affect the calibration results. In such cases, you should recalibrate your system.

3If you selected ‘Reverb Measurement’, select EQ ON or OFF, then START.

3e.EQ Professional			3e1.Reverb Measurement
MCACC	: M1.MEMORY 1		Now Analyzing…		(2/5)
Reverb	Measure with
			Environment Check
		EQ OFF
			Ambient Noise	[	OK ]
	[ START ]		Microphone	[	]
			Speaker Level	[	]
		:Cancel		:Cancel

The following options determine how the reverb characteristics of your listening area are displayed in Reverb View:

•EQ OFF – You will see the reverb characteristics of your listening area without the equalization performed by this receiver (before calibration).

•EQ ON – You will see the reverb characteristics of your listening area with the equalization performed by this receiver (after calibration).2 Note that the EQ response may not appear entirely flat due to adjustments necessary for your listening area.

When the reverb measurement is finished, you can select Reverb View to see the results on-screen. See Professional Calibration EQ graphical output on page 84 for troubleshooting information.

Using Acoustic Calibration EQ Professional

1 Select ‘EQ Professional’, then press ENTER.

3.Manual MCACC 3 e.EQ Professional

4If you selected ‘Reverb View’, you can check the reverb characteristics for each channel. Press RETURN when you’re done.

a . Fine	Channel Level				3e2.Reverb		View
b . Fine SP Distance		1	. Reverb Measurement
c . Standing Wave		2	.Reverb View		M1 : EQ	OFF
d . EQ	Adjust	3	. Advanced EQ	Setup	Ch	L	Fq [	125Hz ]
e . EQ	Professional				dB
	:Return	ENTER:Next		:Return
					0		80	160ms
								:Return

2Select an option and press ENTER.

•Reverb Measurement – Use this to measure the reverb characteristics of your room.

•Reverb View – You can check the reverb measurements made for specified frequency ranges in each channel.1

•Advanced EQ Setup – Use this to select the time period that will be used for frequency adjustment and calibration, based on the reverb measurement of your listening area. Note that customizing system calibration using this setup will alter the settings you made in Automatically setting up for surround sound (Auto MCACC) on page 10 or Automatic MCACC (Expert) on page 38 and is not necessary if you’re satisfied with these settings.

This appears according to the setting you chose in Reverb Measurement (step 3 on page 45). Use / to select the channel and the frequency you want to check. Use / to go back and forth between the two. Note that the markers on the vertical axis indicate decibels in 2 dB steps.

Note

1If the Reverb View procedure is performed after the Automatically setting up for surround sound (Auto MCACC) on page 10 or Reverb Measurement operation, depending on the standing wave control setting, differences may appear on the reverb graph. With the Auto MCACC function, the reverberations are measured with the standing waves controlled, so the reverb characteristics graph shows the characteristics with the effect of the standing waves eliminated. By contrast, the Reverb Measurement function measures the reverberations without controlling the standing waves, so the graph indicates the reverb characteristics including the effect of the standing waves. If you wish to check the reverb characteristics of the room itself (with the standing waves as such), we recommend using the Reverb Measurement function.

2The calibration corresponding to the currently selected MCACC preset will be used when EQ ON is selected. To use another MCACC preset, exit the System Setup menu and press MCACC to select it before pressing SETUP.

45

En