Pioneer VSX-1018AH-K manual Video, Settings

Page 83

Additional information

13

Video

Symptom

Remedy

No image is output when an

• Check the video connections of the source component (see page 18).

input is selected.

• For high-definition video (using component video connections), or when digital video conversion

 

is switched off (in Setting the Video options on page 72), you must connect your TV to this receiver

 

using the same type of video cable as you used to connect your video component.

 

• Make sure the input assignment is correct for components connected using component or HDMI

 

cables (see The Input Setup menu on page 67).

 

• Check the video output settings of the source component.

 

• Check that the video input you selected on your TV is correct.

 

• Some components (such as video game units) have resolutions that may not be converted. If

 

adjusting this receiver’s Resolution setting (in Setting the Video options on page 72) and/or the

 

resolution settings on your component or display doesn’t work, try switching Digital Video

 

Conversion (in Setting the Video options on page 72) OFF.

 

 

Can’t record video.

• Check that the source is not copy-protected.

 

• The video converter is not available when making recordings. Check that the same type of video

 

cable is used for connecting both the recorder and the video source (the one you want to record) to

 

this receiver.

 

 

Noisy, intermittent, or distorted

• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the

picture.

video quality may just be poor (with some video game units, for example). The picture quality may

 

also depend on the settings, etc. of your display device. Switch off the video converter and reconnect

 

the source and display device using the same type of connection (component or composite), then

 

start playback again.

 

 

Settings

Symptom

Remedy

The Auto MCACC Setup

• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see

continually shows an error.

also Problems when using the Auto MCACC Setup on page 11). If the noise level cannot be kept low

 

enough, you will have to set up the surround sound manually (page 41).

 

 

After using the Auto MCACC

• There may have been some low frequency noise in the room from an air-conditioner, motor, etc.

Setup, the speaker size setting

Switch off all other appliances in the room and use Auto MCACC Setup again.

is incorrect.

• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some

 

cases. Change the speaker setting manually in Speaker Setting on page 48, and use the ALL (Keep

 

SP System) option for the Custom Menu in Automatic MCACC (Expert) on page 38 if this is a

 

recurring problem.

 

 

Can’t adjust the Fine Speaker

• Check that the speakers are all in phase (make sure the positive (+) and negative (–) terminals are

Distance setting (page 42)

matched up properly).

properly.

 

The display shows KEY LOCK ON when you try to make settings.

•With the receiver in standby, press  STANDBY/ON while holding down the SPEAKERS button to disable the key lock.

Most recent settings have been • The power cord was disconnected from the wall while adjusting this setting. erased.

83

En

Page 82 Page 84
Image 83
Page 82 Page 84
Contents VSX-1018AH-K Keep in a Secure AREA. this is for Your Security Operating EnvironmentFederal Communications Commission Declaration of Conformity Model Number VSX-1018AH-K Responsible Party NameRisk of Electric Shock Do not Open Wash hands after handling Contents Hdmi Control Other SettingsUsing other functions Other connectionsBefore you start Chapter FeaturesBefore you start Loading the batteries Installing the receiverBefore you start Checking what’s in the boxListening to Surround Sound Minute guideMinute guide Chapter Introduction to home theaterStart Select the input source you want to play Problems when using the Auto Mcacc SetupMinute guide Playing a sourcePhase Control indicator on the front panel lights Better sound using Phase ControlPhase Control on Phase Control OFFRear panel Connecting your equipmentConnecting your equipment Chapter Connecting your equipment About the video converter Connecting your equipment When making cable connectionsAbout Hdmi Connecting your equipment Connecting using HdmiConnect using an Hdmi cable Connecting your equipment Connecting your TV and DVD playerConnecting your Blu-ray disc player Connect using a standard video cableFor a second recorder, use the DVR2 in inputs Use a three-way component video cable Using the component video jacksConnecting digital audio sources Use an optical cable for the connection.2Use a coaxial cable for the connection Connecting analog audio sourcesConnecting a component to the front panel inputs About the WMA9 Pro decoderConnecting the speakers Connecting your equipment Installing your speaker systemBanana plug connections Bare wire connectionsPlacing the speakers Connecting external antennas Connecting antennasPlug the power cord into a power outlet Connecting your equipment Plugging in the receiver12 13 Controls and displaysControls and displays Chapter Front panelSpeakers Operating range of remote control unitControls and displays Controls and displays Display RECEIVER Controls and displays Remote controlReceiver TV CtrlSOURCE MuteListening in surround sound Listening to your systemListening to your system Chapter Auto playbackPro Logic IIx Music See Using the Advanced surround effectsListening to your system Listening in stereoSelecting Mcacc presets Listening to your system Using Front Stage Surround AdvanceUsing Stream Direct Hdmi Digital Analog Choosing the input signalUsing surround back channel processing Using the Virtual Surround Back mode Sources Using the genre synchronizing functionDTS-HD Master Audio/DTS-HD DTS-EXPRESS encoded stereo Listening to the radio Using the tunerUsing the tuner Chapter Saving station presetsAbcdefghijklmnopqrstuvwxyz Using the tunerNaming station presets Listening to station presetsSelect the setting you want to adjust System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuMcacc System Setup menuIf necessary, confirm the speaker configuration OSD.1 Manual Mcacc setup Surround back speaker settingFine Speaker Distance Adjust the level of the left channelSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Fine Channel LevelStanding Wave Acoustic Calibration EQ AdjustFrequency response of your room.1 How to use Acoustic Calibration EQ ProfessionalHow to interpret the graphical output Acoustic Calibration EQ ProfessionalSelect an option and press Enter Using Acoustic Calibration EQ ProfessionalSelect ‘EQ Professional’, then press Enter Data Management Select ‘Data Management’ from the System Setup menuClearing Mcacc presets Checking Mcacc preset dataCopying Mcacc preset data Renaming Mcacc presetsSelect ‘Speaker Setting’ from the Manual SP Setup menu System Setup menu Manual speaker setupSpeaker Setting Select ‘Manual SP Setup’, then press EnterChannel Level Select a setup optionConfirm your selected setup option Adjust the level of each channel using /Curve Speaker DistanceOther connections Chapter Connecting an iPodConnecting your iPod to the receiver Other connectionsBasic playback controls Switching the iPod controls2Other connections Basic playback controls Other connections Connecting a USB deviceConnecting your USB device to the receiver Switch on the receiver and your TVCompressed audio compatibility Using XM RadioConnecting your XM Radio receiver Listening to XM Radio Using XM HD SurroundSaving channel presets Using the XM MenuListening to Sirius Radio Using Sirius RadioConnecting your Sirius Connect Tuner Press Sirius to switch to the Sirius inputSirius Menu provides additional Sirius Radio features.2 Connecting the multichannel analog inputsUsing the Sirius Menu Press / to select the channel preset you wantSelecting the multichannel analog inputs Speaker B setupSwitching the speaker system Are for the Speaker B setting only.2Connect your speakers as shown below Bi-wiring your speakersBi-amping your front speakers Large Other connections Connecting additional amplifiersMULTI-ZONE listening Making MULTI-ZONE connectionsMULTI-ZONE listening options Using the MULTI-ZONE controlsBasic MULTI-ZONE setup Zone Surround Back System MULTI-ZONE setup ZonePress Control Connecting an IR receiverMULTI-ZONE remote controls Use the Master Volume dial to adjust the volumeVideo ANT MPX Signal SEL Hdmi Control Chapter Setting the Hdmi optionsSetting the Hdmi Control mode Hdmi ControlAbout Hdmi Control Synchronized amp modeBefore using synchronization Hdmi ControlSetup Other SettingsOther Settings Chapter Input Setup menuPress Receiver on the remote control, then press Setup Other SettingsOther Setup menu Input function default and possible settingsZone Audio Setup Multi Channel Input SetupSelect the ‘PDP Volume Control’ setting you want SR+ Setup for Pioneer flat panel TVsOSD Adjustment Select ‘SR+ Setup’ from the Other Setup menuPress Return to confirm and exit the menu Using other functionsUsing other functions Chapter Setting the Audio optionsIMAGEh Using other functionsSetting the Video options AUTOcTune to the radio station, load the CD, video, DVD, etc Making an audio or a video recordingSelect the source you want to record Prepare the source you want to recordDimming the display Using the sleep timerSwitching the speaker impedance Checking your system settingsPress Sound Retriever to confirm Resetting the systemDefault system settings Press the front panel Auto SURR/STREAM Direct buttonControlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Preset code listControls for TVs Controlling the rest of your systemVOL + Controls for other componentsTV  CH +Decide which component you want to use the remote sensor Additional information Chapter Troubleshooting Power Additional informationAdditional information Other audio problems Video SettingsDisplay Signal SEL buttonProfessional Calibration EQ graphical output USB interface Remote controlHdcp Error shows Or other setting for your componentOther setting for your component Receiver to a component or TV with the DeepColor featureXM radio messages Configuration aConfiguration B Important information regarding the Hdmi connectionSirius radio messages Dolby Additional information Surround sound formatsDTS 96/24 Windows Media Audio 9 ProfessionalDTS Digital Surround DTS Neo6About XM Radio XM Ready Legal Additional information About XMAbout Sirius About Neural THX SurroundNeural THX b Stereo 2 channel signal formatsPRO Logic a PRO Logic DTS +Neo6 Multichannel signal formatsDTS +2 Pro Logic llx Movie a DTS +2 Pro Logic llx MusicDolby Digital Plus Straight decoding Dolby Digital Surround Direct Pure DirectAdditional information Specifications Additional information Cleaning the unit Decibel Level Example To establish a safe levelOnce you have established a comfortable sound level Pioneer Corporation

VSX-1018AH-K specifications

The Pioneer VSX-1018AH-K is a powerful home theater receiver that embodies a blend of quality, features, and innovative technology, making it a standout choice for audio enthusiasts and casual listeners alike. This 7.1-channel receiver boasts a robust output of 110 watts per channel, designed to deliver immersive audio across various environments.

One of the key features of the VSX-1018AH-K is its support for advanced audio formats, including Dolby TrueHD and DTS-HD Master Audio. These formats provide a lossless soundtrack experience, ensuring that audio reproduction remains faithful to the original source. This receiver is also equipped with Pioneer’s proprietary MCACC (Multi-Channel Acoustic Calibration System), which allows users to optimize sound settings based on their specific room acoustics. By analyzing and adjusting the sound fields, MCACC ensures that every listener enjoys an enhanced audio experience.

In terms of connectivity, the VSX-1018AH-K excels with its array of inputs and outputs. It includes multiple HDMI inputs, allowing users to seamlessly connect various devices such as Blu-ray players, gaming consoles, and streaming devices. Additionally, it supports HDMI version 1.3, which means it can handle high-definition video signals and deep color technology, enhancing the overall viewing experience.

For those who appreciate versatility, this receiver also features built-in support for both wireless and wired network audio streaming. Users can connect to their home network to enjoy music stored on their devices or access popular streaming services. The USB port allows for easy connection of flash drives, enabling playback of high-resolution audio files.

Moreover, the receiver is equipped with a user-friendly interface and an intuitive remote control, making it easy to navigate through various settings and options. The graphical user interface is designed for simplicity, enabling users to customize preferences without hassle.

The Pioneer VSX-1018AH-K not only focuses on sound but also on video quality, thanks to its upscale capabilities that can convert standard-definition video to high-definition, ensuring that all media looks great on HD displays. Overall, the Pioneer VSX-1018AH-K represents a comprehensive solution for anyone looking to enhance their home theater system, merging advanced technology with user-friendly features aimed at delivering an unparalleled home entertainment experience.
Top Page Image Contents