Pioneer PDP-5000EX manual STANDBY/ON Button, STANDBY/ON Indicator, English

Page 3
D3-4-2-2-2a_A_En
D3-4-2-1-6_A_En
D3-4-2-1-4_A_En

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filed with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

D3-4-2-1-3_A_En

This product complies with the Low Voltage Directive (73/23/EEC, amended by 93/68/EEC), EMC Directives (89/336/EEC, amended by 92/31/EEC and 93/68/EEC).

WARNING

Before plugging in for the first time, read the following section carefully.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V or 120 V) written on the rear panel.

WARNING

This apparatus must be earthed.

WARNING

This product equipped with a three-wire grounding (earthed) plug - a plug that has a third (grounding) pin. This plug only fits a grounding-type power outlet. If you are unable to insert the plug into an outlet, contact a licensed electrician to replace the outlet with a properly grounded one. Do not defeat the safety purpose of the grounding plug.

The following symbols are found on labels attached to the product. They alert the operators and service personnel of this equipment to any potentially dangerous conditions.

English

WARNING

This symbol refers to a hazard or unsafe practice which can result in personal injury or property damage.

CAUTION

This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death.

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A_En

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation. For the minimum space required, see page 16.

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

CAUTION

The POWER switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

STANDBY/ON Button

STANDBY: When placed into the standby mode, the main power flow is cut and the unit is no longer fully operational.

STANDBY/ON Indicator

The indicator is lit red when the unit is in the standby mode and is lit blue when it is in the power-on mode.

Page 2 Page 4
Image 3
Page 2 Page 4
Contents PDP-5000EX Important the Moulded Plug STANDBY/ON Indicator STANDBY/ON ButtonEnglish Contents Appendix Enjoying through External EquipmentInstallation guidelines Important User Guidance InformationUsage guidelines Information of cell defect When not using the product for a long period of timeCleaning the cabinet Plasma Display protection functionPanel sticking and after-image lag Safety Precautions Wall-mount installation of the unit Side view diagram Rear view diagramSupplied Accessories Main unit Part NamesMain unit Operation panel on the main unitWhen handling the remote control unit Remote control unitSpeaker R terminals Connection panelInstalling the Plasma Display Using the optional Pioneer stand Operating EnvironmentLocation Using a wall for stabilization Preventing the Plasma Display from Falling OverStabilizing on a table or floor Connecting the power cord Connecting the speakersAttaching the ferrite core To remove speed clamps How to route cablesOrganize cables together using the provided speed clamps To attach the speed clamps to the main unitPreparing the remote control unit Allowed operation range of the remote control unitInserting batteries Plasma Display status indicators Changing the volume and soundOperation For AV source Use the multiscreen functions Confirming current statusAV Selection Splitting the screenSelecting a screen size manually Menu operations Using the menuAV mode menus PC mode menusAdvanced picture adjustments Basic Adjustment SettingsLanguage setting Basic picture adjustmentsColor Temp Using Color TempUsing CTI Using Color ManagementUsing the Dynamic Range Expander DRE functions Using the 3DYC and I-P ModeReducing the noise in images Sound adjustments Front SurroundMode Energy Save Power ControlNo Signal off Power ManagementSwitching the vertical drive frequency AV mode only Adjusting image positions AV mode onlyAdjusting image positions and clock manually PC mode only Color system setting Selecting an input signal typeSelecting a screen size automatically AV mode only Watching a decoder or VCR image Using Hdmi InputConnecting a decoder or VCR Enjoying through External EquipmentHdmi equipment To activate the Hdmi terminal Connecting Hdmi equipmentTo specify the type of digital video signals To specify the type of audio signalsWatching a DVD image Using DVI InputConnecting DVI equipment Connecting a DVD playerWatching an image from a personal computer Enjoying a game console or watching camcorder imagesAbout SR+ Connecting control cordsComputer compatibility chart Resolution Frequency RemarksCode Message Check TroubleshootingProblem AppendixTrademarks Specifications
Top Page Image Contents