Pioneer PDP-5000EX manual Use the multiscreen functions Confirming current status, AV Selection

Page 22

07Operation

Use the multiscreen functions

Confirming current status

Splitting the screen

Use the following procedure to select 2-screen mode.

SPLIT

SUB

INPUT

VOLUME MUTING

SWAP

1Press the remote control unit’s SPLIT.

The main screen is displayed on the left and the subscreen on the right.

Main screen

Sub screen

2Press the remote control unit’s SUB INPUT to select the subscreen input source.

To exchange the main screen and subscreen inputs Press the remote control unit’s SWAP.

The right and left sides of the display will switch; what was previously the main screen will now show the subscreen, and vice versa.

STANDBY/ON

 

SCREEN AUTO

AV

SIZE SETUP DISPLAY

SELECTION

PC

 

1Press the remote control unit’s DISPLAY.

The currently selected input source and settings will be displayed.

Display example: Under normal conditions (with video signal input)

INPUT2

1080i

STANDARD

FULL

AV Selection

Select from the five viewing options, depending on the current environment (e.g., room brightness), the type of images input from external equipment.

Each time the remote control unit’s AV SELECTION is pressed, the AV function alternates.

STANDBY/ON

 

SCREEN AUTO

AV

SIZE SETUP DISPLAY

SELECTION

PC

 

NOTE

•The multiscreen function cannot display images from the same input source at the same time. If you make such an attempt, a warning message appears.

•The multiscreen function cannot display images from INPUT2 and INPUT3 simultaneously. If you make such an attempt, a warning message appears.

•When you press HOME MENU the single-screen mode is restored and the corresponding menu is displayed.

•When in the 2-screen mode, images displayed on the right screen may look less fine, depending on the images.

•If you select 1920*1080p@24 Hz for the main screen in the 2- screen mode, video images may not be displayed properly because of the Plasma Display’s capability.

•PAL 60 signals are not suited for image display on the Sub screen.

•If the multiscreen function is used continuously for several hours, or for shorter periods of time over several days, a permanent after-image may remain on the screen due to burning of the fluorescent materials.

22

For AV source

Item

Description

STANDARD

For a highly defined image in a normally bright

 

room

 

You can set the mode for each input source.

 

 

DYNAMIC

For a very sharp image with the maximum

 

contrast

 

This mode does not allow manual image quality

 

adjustment.

 

 

MOVIE

For a movie

 

You can set the mode for each input source.

 

 

GAME

Lowers image brightness for easier viewing

 

You can set the mode for each input source.

 

 

USER

Allows the user to customize settings as

 

desired.

 

You can set the mode for each input source.

 

 

En

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PDP-5000EX Important the Moulded Plug STANDBY/ON Button STANDBY/ON IndicatorEnglish Contents Enjoying through External Equipment AppendixImportant User Guidance Information Installation guidelinesUsage guidelines Plasma Display protection function When not using the product for a long period of timeCleaning the cabinet Information of cell defectPanel sticking and after-image lag Safety Precautions Wall-mount installation of the unit Rear view diagram Side view diagramSupplied Accessories Operation panel on the main unit Part NamesMain unit Main unitRemote control unit When handling the remote control unitConnection panel Speaker R terminalsUsing the optional Pioneer stand Operating Environment Installing the Plasma DisplayLocation Preventing the Plasma Display from Falling Over Using a wall for stabilizationStabilizing on a table or floor Connecting the speakers Connecting the power cordAttaching the ferrite core To attach the speed clamps to the main unit How to route cables Organize cables together using the provided speed clamps To remove speed clampsAllowed operation range of the remote control unit Preparing the remote control unitInserting batteries Changing the volume and sound Plasma Display status indicatorsOperation Splitting the screen Use the multiscreen functions Confirming current statusAV Selection For AV sourceSelecting a screen size manually PC mode menus Using the menuAV mode menus Menu operationsBasic picture adjustments Basic Adjustment SettingsLanguage setting Advanced picture adjustmentsUsing Color Management Using Color TempUsing CTI Color TempUsing the 3DYC and I-P Mode Using the Dynamic Range Expander DRE functionsReducing the noise in images Front Surround Sound adjustmentsMode Power Management Power ControlNo Signal off Energy SaveAdjusting image positions AV mode only Switching the vertical drive frequency AV mode onlyAdjusting image positions and clock manually PC mode only Selecting an input signal type Color system settingSelecting a screen size automatically AV mode only Enjoying through External Equipment Using Hdmi InputConnecting a decoder or VCR Watching a decoder or VCR imageTo specify the type of audio signals Connecting Hdmi equipmentTo specify the type of digital video signals Hdmi equipment To activate the Hdmi terminalConnecting a DVD player Using DVI InputConnecting DVI equipment Watching a DVD imageEnjoying a game console or watching camcorder images Watching an image from a personal computerResolution Frequency Remarks Connecting control cordsComputer compatibility chart About SR+Appendix TroubleshootingProblem Code Message CheckSpecifications Trademarks
Top Page Image Contents