Panasonic TH-PH10 manual Connections, Speakers, AC cord ﬁxing

Page 9

Unplug the AC cord pressing the two knobs.

Connections

When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation. (Example: TH-42PH10UK)

Speakers (Optional accessories)

SPEAKERS

Terminals (L)

SPEAKERS	AC cord connection (see page 13)
Terminals (R)	AC cord connection (see page 13)
	– AC cord ﬁxing

1
2	1
	1
	2

Plug the AC cord into the display unit. Plug the AC cord until it clicks.

Note:

Make sure that the AC cord is locked on both the left and right sides.

–Cable ﬁxing bands

Secure any excess cables with bands as required.

Unplug the AC cord

Note:

When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet ﬁrst.

Pass the attached cable ﬁxing band through the clip as shown in the ﬁgure.

1

To secure cables connected to Terminals, wrap the cable ﬁxing band around them then pass the pointed end through the locking block, as shown in the ﬁgure.

While ensuring there is sufﬁcient slack in cables to minimize stress (especially in the power cord), ﬁrmly bind all cables with the supplied ﬁxing band.

To tighten:	To loosen:
	Push the catch
Pull
2	Pull

R AUDIO	L	S VIDEO R	AUDIO	L	VIDEO	R AUDIO L	PR/CR/R PB/CB/B	Y/G			AUDIO
B		AV IN		A		COMPONENT/RGB IN
SLOT1		SLOT2					SLOT3		PC	IN	SERIAL

	Optional Terminal		Dual Video Terminals		COMPONENT/RGB IN and
	Board Insert Slot		(equivalent of BNC		Audio IN Terminals (equivalent
	(covered)		Dual Video Terminal		of BNC Component Video
			Board (TY-FB9BD))		Terminal Board (TY-42TM6A))
Notes:			(see page 12)		(see page 12)

•At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3.

•TH-37PH10UK has two slots only.

From EXTERNAL monitor terminal on Computer (see page 10)

From SERIAL Terminal on Computer (see page 11)

9

Image 9

Contents Operating Instructions Manual de instrucciones English EspañolModel No. Número de modelo Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents Trademark Credits FCC Statement When using the Plasma Display Safety PrecautionsSafety Precautions / Maintenance MaintenanceSetup AC Power Supply CordAccessories Accessories SuppliedRemote Control Batteries Connections SpeakersAC cord ﬁxing Signal Names for Mini D-sub 15P Connector PC Input Terminals connectionConnections Serial Terminals connection CommandCommunication parameters Basic format for control dataAV & Component / RGB connection RGB signal R, G, BConnecting the AC cord plug to the Plasma Display Power on / OFFConnecting the plug to the Wall Outlet Fix the AC cord plug securely to the Plasma Display. seeBasic Controls Basic Controls On-Screen Menu Displays VA N C E D SettingsTime / Power OFF Time On Time / Power OFFOn-Screen Menu Displays Initial selections Selecting the input signalSelecting the On-Screen Menu Language INPUT1A INPUT1B INPUT2 PCNormal Zoom Full Aspect ControlsPanasonic Auto During Multi PIP OperationsClock Phase Adjusting POS. /SIZERGB/PC in mode Eliminate the ﬂickering and distortionMulti PIP One screen Advanced PIP Press to exit from Options menu Advanced PIPSub screen Main screen 1280x768@60Hz DVIAdvanced Settings on Picture AdjustmentsAdvanced Settings OFF Standard Cinema DynamicPicture Adjustments Advanced SettingsEffect Adjustments Effect DetailsMute Sound AdjustmentDisplay the operation guide Digital ZoomPosition Select the magniﬁcation required for the enlarged displayPresent Time Setup Press to set up DAY or Present Time of DAYButton Forward SET UP Timer Display the SET UP Timer Screen Press to selectPower on Time / Power OFF Time Start setting Mode selectionScreensaver For preventing image retention Negative / Scroll selectionSetup of Screensaver Time Reduces screen image retentionScreensaver For preventing image retention Side BAR Adjust OFF Dark MID BrightPress to exit from Screensaver Reduces power consumption Customizing the Input labelsAddition sign Selected Input How to setup Multi Display SET UP for Multi DisplayPress to select Vertical Scale Press to select × 1, × 2, × 3, ×Display Number locations for each arrangement Examples SET UP for Multi DisplayID Remote Control Function Seam Hides Video SettingID remote control button operation ID CancellationComponent / RGB in Select SET UP for Input Signals3D Y/C Filter For Ntsc AV images SelectSET UP for Input Signals Color System / Panasonic AutoPulldown / Video NR Sync Setting RGB sync signalRefresh Rate FREQ. kHz / V-FREQ. HzOptions1/3 Options AdjustmentsOff Initial VOL Sets normal volume Level Options AdjustmentsEnable Normalization Weekly Command Timer Press to select Time / Command Press to select a command numberTime Set the time to execute a command program Press to set each itemShipping condition Plasma Display panel TroubleshootingVideo input VIDEO/COMPONENT/RGB/PC input signalsPAL60 RGBCommand list of Weekly Command Timer TH-37PH10UK TH-42PH10UK SpeciﬁcationsTH-50PH10UK TH-58PH10UK SpeciﬁcationsLimits and Exclusions Limited Warranty Statement Panasonic Broadcast & Television Systems Company Customer’s RecordExecutive Ofﬁce Panasonic Canada Inc