Panasonic TH-42PF11UK, TH-65PF11UK, TH-58PF11UK Initial selections, Selecting the input signal

Page 15

Initial selections

Initial selections

Selecting the input signal

Select the input signals to be connected by installing the optional Terminal Boards.

Press to select the input signal to be played back from the equipment which has been connected to the Plasma Display.

Input signals will change as follows:

INPUT1 INPUT2A INPUT2B INPUT3 PC

SLOT2 is for dual input so that you can select INPUT2A or

INPUT2B for INPUT2.

INPUT2A : HDMI signal terminal in SLOT2

INPUT2B : HDMI signal terminal in SLOT2

Press the INPUT “1”, “2”, “3” or “PC” input mode selection

button to select the INPUT mode.

Press to switch the input mode between INPUT2A and INPUT2B.

Notes:

•Selecting is also possible by pressing the INPUT button on the unit.

•Input terminal will not be selected if the terminal board is not installed into the SLOT.

•Select to match the signals from the source connected to the component/RGB input terminals. (see page 39)

•In two-screen display, the same input mode cannot be selected for the main picture and sub picture.

•Image retention (image lag) may occur on the plasma display panel when a still picture is kept on the panel for an extended period. The function that darkens the screen slightly is activated to prevent image retention (see page 49), but this function is not the perfect solution to image retention.

INPUT MENU -/ VOL +/ ENTER/

Selecting the On-Screen Menu Language

Press to display the SET UP menu. Press to select OSD LANGUAGE. Press to select your preferred language.

Selectable languages

English(UK)

Deutsch

Français

Italiano

Español

ENGLISH(US)

.......(Chinese)

.......(Japanese)

Русский .......(Russian)

SET UP	1/2

SIGNAL

SCREENSAVER

COMPONENT/RGB-IN SELECT

	RGB

INPUT LABEL	PC

POWER SAVE	OFF

STANDBY SAVE	OFF

POWER MANAGEMENT	OFF

AUTO POWER OFF	OFF

OSD LANGUAGE	ENGLISH (US)

15

Image 15

Contents TH-42PF11UK TH-50PF11UK TH-58PF11UK TH-65PF11UK High Deﬁnition Plasma Display Alta deﬁnición Pantalla de plasmaOperating Instructions Manual de instrucciones English EspañolRISK OF ELECTRIC SHOCK DO NOT OPEN Important Safety Instructions Dear Panasonic Customer Table of ContentsTrademark Credits FCC STATEMENTFCC CAUTION CANADIAN NOTICEBe sure to disconnect all cables before moving the Plasma Display Safety PrecautionsWhen using the Plasma Display Clean the power cable regularly to prevent it from becoming dustyAC Power Supply Cord MaintenanceSafety Precautions / Maintenance SetupCheck that you have the Accessories and items shown AccessoriesAccessories Supplied Remote Control BatteriesConnections AC cord ﬁxingCable ﬁxing band PC Input Terminals connection ConnectionsSignal Names for Mini D-sub 15P Connector Communication parameters SERIAL Terminals connectionSignal names for D-sub 9P connector CommandHDMI connection COMPONENT / RGB connectionSLOT2 Power ON / OFF Connecting the AC cord plug to the Plasma DisplayConnecting the plug to the Wall Outlet OSD LANGUAGE Power ON / OFFWhen ﬁrst switching on the unit PRESENT TIME SETUPSelecting the input signal Initial selectionsSelecting the On-Screen Menu Language Volume Adjustment Basic ControlsMain Unit Remote control sensorChannel Adjustment Remote Control TransmitterBasic Controls SET UP button see page SOUND button see page DIRECT INPUT buttonsASPECT Controls Panasonic AUTOAll Aspect mode Selecting the Display Mode MULTI PIP SETUPMULTI PIP ASPECT ControlsTransparent Function and Insertion Function MULTI PIPSwapping Screens During Blend PIP Composite Screen Functionthe main screen Selecting the Target Screen for OperationsSelecting the Sub Screen Position During P IN P Display Operations onSelect the area of the image to be enlarged Digital Zoom1 Display the operation guide During Digital Zoom, only the following buttons can be operatedUnit Remote Control Display the menu screenOn-Screen Menu Display Select the itemAdjust the horizontal size Adjusting POS. /SIZEAdjust the horizontal position Adjust the vertical positionNORMALIZE Adjusting POS. /SIZEHelpful Hint NormalizationCINEMA PICTURE AdjustmentsSTANDARD DYNAMICEffect ADVANCED SETTINGSPICTURE Adjustments AdjustmentsSDI SOUND OUTPUT SOUND AdjustmentPress to select POWER ON TIME / POWER OFF TIME PRESENT TIME SETUP / SET UP TIMERPRESENT TIME SETUP SET UP TIMERFUNCTION selection Setup of SCREENSAVER Time5 START setting SCREENSAVER For preventing image retentionSIDE BAR ADJUST Reduces screen image retentionSCREENSAVER For preventing image retention AUTO POWER OFF Reduces power consumptionSIGNAL POWER SAVESelected Input Customizing the Input labelsDISPLAY ORIENTATION Addition signExamples SET UP for MULTI DISPLAYHow to setup MULTI DISPLAY Display Number locations for each arrangementID Cancellation ID Remote Control FunctionSET UP for MULTI DISPLAY ID remote control button operationTransparent Display of the Sub Screen During BLEND PIP MULTI PIP SETUPMULTI PIP DISPLAY MODEHow to setup PORTRAIT SET UP for PORTRAITWhen PORTRAIT SETUP “ON” SET UP for PORTRAIT6 AI-SYNCHRONIZATION LOCATION settingSET UP for Input Signals COMPONENT / RGB IN SELECTYUV / RGB IN SELECT Press to exit from adjust mode SIGNAL menuSET UP for Input Signals 3D Y/C FILTER - For NTSC AV imagesIf the image becomes unstable COLOR SYSTEM / Panasonic AUTO32 PULLDOWN XGA MODEREFRESH RATE NOISE REDUCTIONAdvanced NR SYNC Input signal displaySetting RGB sync signal Displays the frequency and the type of the current input signalOptions Adjustments Press to display the Setup menu Press to select “OSD Language”Press to adjust the menu Press to exit from Options menu User2 Options Adjustmentsbutton on main unit together with button on the remote control and hold for more than 5 seconds. TheNormalization Press theWeekly Command Timer SHIPPING Shipping conditionSound TroubleshootingPlasma Display panel PictureList of Aspect Modes In the case of SD signals, pictures with a 43 aspect ratio areenlarged horizontally, and displayed. This mode is suited to Note Signals without above speciﬁcation may not be displayed properly Applicable Input Signals∗4 The input signal is recognized as 1,125 1,080 / 60p TY-FB11DHD is installedVIDEO input HDMI Applicable Input SignalsCommand list of Weekly Command Timer Speciﬁcations Speciﬁcations Warranty for the U.S.A and Puerto RicoPanasonic Professional Flat Panel Display Limited Warranty In the USA and Puerto Rico FOR SERVICE CALL TOLL FREEWarranty Service LIMITED WARRANTY STATEMENTfor Canada WARRANTY COVERAGE PERIOD EXCEPTIONSPage Page Panasonic Canada Inc Customer’s RecordPanasonic Professional Display Company Executive Ofﬁce

Related manuals

Manual 59 pages 22.18 Kb