Panasonic TH-58PF11UK, TH-65PF11UK, TH-50PF11UK, TH-42PF11UK manual Options Adjustments, User2

Options Adjustments

Item						Adjustments
	Off	PC	INPUT1	INPUT2		INPUT3
	Locks the input switch operation.
	Notes:
	• Only the adjusted signal is displayed (see page 15).
INPUT lock	• Signal can be displayed when the Terminal board is installed.
	• Input switch can be used when this is set to “Off”.
	• In two screen display mode, if anything other than “Off” is set, the value will be fixed as the value input in
	the single screen display mode.
	• When a dual input terminal board is attached, A or B is displayed depending on the selected input signal.
	(Ex. INPUT1A, INPUT1B)
	Off	MENU&ENTER		On
	Off: All the buttons on main unit can be used.
	MENU&ENTER: Locks			and	buttons on main unit.

				MENU	ENTER/
Button lock	On: Locks all the button on main unit.
	Sets Button lock with the unit buttons in the following procedure.
	Off: Press		four times→Press			four times→Press		four times→Press
	MENU&ENTER: Press					INPUT	four times→Press		ENTER/
					four times→Press				four times→Press
	On: Press			ENTER/		four times→Press			INPUT	ENTER/
			four times→Press					four times→Press
						ENTER/			ENTER/
	Off	User1		User2		User3
	Off:	You can use all of the buttons on the remote control.
Remocon User level	User1:You can only use				,	, ,	, ,	, ,	buttons on the remote control.
	User2:You can only use				,	buttons on the remote control.

User3:Locks all the buttons on remote control.

	Enable: Enables the “Off-timer function”.
Off-timer function	Disable:			Disables the “Off-timer function”.
	Note:			When “Disable” is set, the Off-timer is cancelled.
	Normal			Standby	On
	Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.
Initial Power Mode	Normal: Power returns in as the same state as before the power interruption.
	Standby: Power returns in standby mode. (Power Indicator : red/orange)
	On:			Power returns in power On. (Power Indicator : green)
	Note: When using multiple displays, “Standby” is preferred to be set in order to reduce a power load.
	Sets panel ID number when panel is used in “Remote ID” or “Serial ID”.
ID select	Set value range: 0 - 100
	(Standard value: 0)
	Off:		Disables ID remote control functions. You can use normal remote control operations.
	On:		Enable ID remote control functions.
Remote ID	Note: To use the ID remote control function, it is necessary to set each ID number of remote control and
		display unit. About the setting method, please refer to “ID Remote Control Function” (see page 35)
		and “ID select” (above-mentioned).
	Sets the panel ID Control.
Serial ID	Off:		Disables external control by the ID.
	On:		Enables the external control by the ID.
	Adjusts the image display size on screen.
	Off:		Sets the normal image display size on screen.
	On:		Sets the image display size approximately 95 % of the normal image display.
				Off		On
Display size	Notes:
	• This setting is valid only when the input signals are as follows;
	NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (BNC Dual Video Terminal Board (TY-FB9BD))
	525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p,
	1125/60p, 1125/50p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)
	• This setting is invalid when two screen display, digital zoom, Multi display or Portrait display is selected.
	• When “Display size” is set to “On”, “H-POS” and “V-POS” in “POS. /SIZE” can be adjusted.
	• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.

45