SET UP for Input Signals
COLOR SYSTEM / Panasonic AUTO
Select SIGNAL from the “SET UP” menu during VIDEO (S VIDEO) input signal mode.(“SIGNAL [VIDEO]” menu is displayed.)
| Press to select the “COLOR SYSTEM” or “Panasonic AUTO”. |
|
|
|
| |||||
|
| SIGNAL | [ VIDEO ] |
| ||||||
| Press to select each function. |
|
|
|
|
|
|
| ||
|
|
|
|
| 3D Y/C FILTER (NTSC) | ON |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| COLOR SYSTEM | AUTO |
| |
|
|
|
|
|
|
|
|
| ||
| If the image becomes unstable: |
|
|
|
| 3 : 2 PULLDOWN | OFF |
| ||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| Panasonic AUTO (4 : 3) | 4:3 |
|
| ||
| With the system set on Auto, under conditions of low level or noisy |
|
|
|
|
| ||||
| input signals the image may in rare cases become unstable. Should this occur, |
|
|
| ||||||
| set the system to match the format of the input signal. |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
Mode |
|
|
| Function |
|
|
|
|
|
|
COLOR SYSTEM | Set the color system to match the input signal. When selecting “AUTO”, the color system is automatically | |||||||||
|
| selected from NTSC/PAL/SECAM, however, M.NTSC signal is not displayed properly depending on | ||||||||
|
| the attached terminal board. To display M.NTSC signal, select “M.NTSC” in COLOR SYSTEM. | ||||||||
|
| AUTO | PAL | SECAM | M.NTSC |
| NTSC |
|
|
|
|
| |||||||||
Panasonic AUTO | Set to “4:3” to view 4:3 images in an unchanged format when Panasonic AUTO is selected. | |||||||||
(4 : 3 ) |
| If you would like to view 4:3 images in Just format, set to “JUST”. |
|
|
| |||||
Note:
Panasonic AUTO does not function when BNC Dual Video Terminal Board
3:2 PULLDOWN
3:2 PULLDOWN: When ON, the display attempts to reproduce a more natural interpretation of sources such as movie pictures, which are recorded at 24 frames per second.
If the picture is not stable, turn the setting to OFF.
Notes:
When ON, this setting only affects the following signal input:
•NTSC / PAL signal input during “VIDEO (S VIDEO)” input signal.
•525i(480i), 625i(575i), 1125(1080)/60i signal input during “COMPONENT” input signal.
Press to select “3:2 PULLDOWN”.
Press to set ON/OFF.
3 : 2 PULLDOWN | OFF |
|
|
XGA MODE
This menu is displayed when the input signal is analog (Component/PC). This unit supports three types of XGA signals with 60Hz vertical frequency having different aspect ratios and sampling rates (1,024 × 768 @ 60Hz, 1,280 × 768 @ 60Hz, and 1,366 × 768 @ 60Hz). Be sure to make settings in accordance with the input signal in order to achieve a more appropriate and attractive display.
In addition, after making this setting, be sure to make each adjustment (such as “AUTO SETUP”) on the “POS. /SIZE” menu as necessary. (see page 24)
Press to select “XGA MODE”.
Press to select “1024×768”, “1280×768” , “1366×768”.
XGA MODE | 1024 × 768 |
|
|
41