Panasonic PT-LM1U Turning off the power, #Press the Power button, Direct power off function

Page 13

Turning off the power

POWER

Power indicator

#

INPUT

VIDEO RGB

AUTO

SETUPMENU

 

ENTER

 

FREEZE

SHUTTER

$

 

STD

 

VOLUME

D.ZOOM

 

 

INDEX

 

 

WINDOW

 

 

PROJECTOR

 

%Powercord

#Press the POWER button.

B“POWER OFF” is displayed on thePOWER OFF

Direct power off function

You can disconnect the power cord during projection or immediately after use and move the projector. The cooling fan will operate by the internal power supply to cool down the lamp.

BWhen this function is used, it may take more time for the lamp to turn back on again compared to when the lamp cools down with the power cord connected.

BDo not put the projector in a bag while the cooling fan is operating.

CAUTION

If not using the projector for an extended period of time, disconnect the power cord plug from the wall outlet.

BIf dust builds up on the power cord plug, the resulting humidity may

damage the insulation, which could result in fire.

Basic Operation

screen.

OK CANCEL

BThis projector continues to draw approximately 5 W of power even when

the power is turned off.

$Press the I or H button to select “OK”, and then press the ENTER button.

BThe lamp unit will switch off and the picture will stop being projected. (The power indicator on the projector will illuminate orange while the cooling fan is still operating.)

%Disconnect the power cord after the power indicator on the projector illuminates red.

NOTE:

BYou can also turn off the power by pressing the POWER button twice or by holding it down for at least 0.5 seconds.

BWhen the projector is in standby mode (the power indicator on the projector is illuminated red), the projector continues to draw approximately 5 W of power even when the cooling fan has stopped.

Power indicator

Power indicator status

Projector status

Red

Illuminated

The projector is in standby mode and image projection

is possible by pressing the POWER button.

 

 

 

 

 

 

 

The projector is preparing for projection after the

 

Flashing

power is turned on while the power indicator is

Green

illuminated red. (After a short period, a picture will be

 

 

 

projected.)

 

Illuminated

A picture is being projected.

 

 

 

 

Illuminated

The lamp is cooling down after the power is turned

 

off. (The cooling fan is operating.)

 

 

Orange

 

The projector is preparing for projection after the

 

power is turned on while the power indicator is

 

Flashing

 

illuminated orange. (After a short period, a picture

 

 

 

 

will be projected.)

 

 

 

24-ENGLISH

ENGLISH-25

Image 13
Contents Model No. PT-LM1U LCD Projector Commercial UsePreparation Dear Panasonic CustomerDeclaration of Conformity Precautions with regard to safety ContentsInsert the power cord plug securely into the wall outlet Do not handle the power cord plug with wet handsDo not place the projector into water or let it become wet Do not place liquid containers on top of the projectorInsulate the battery using tape or similar before disposal AccessoriesDo not put your weight on this projector Do not place any heavy objects on top of the projectorDo not touch the surfaces of the lens with your bare hands Before useScreen Lamp# Connector panel $ Air outlet port Leg adjuster buttons L/RLocation and function of each part Projector control panel Top Menu Projection methods Setting-upConnections Connecting to computerProjector position Projection distancesInsert the battery holder Connecting to video equipmentTurning on the power #Press the Power button Turning off the powerDirect power off function Power indicatorPress the Auto Setup button Pausing a picture FreezeTurning off the picture and sound momentarily Shutter Press the Freeze buttonEnlarging the picture D.ZOOM Adjusting the volume VolumeMenu screens On-screen menusSettings Returning a setting to the factory defaultMenu operation guide Picture Mode Correcting keystone distortion Adjusting the pictureContrast Vertical keystone distortion correction onlySignal Mode Still ModeBright ColorClock Phase Adjusting the positionPosition DOT ClockResizing Changing the display languageFrame Lock Option settings Setting up the security function Text Display Temp indicator Lamp indicatorText Change CareCleaning Cleaning and replacing the air filterReplacement procedure RemedyLamp unit replacement procedure Lamp unit replacement periodReplacing the lamp unit Before calling for service Cleaning and maintenance Remote control unit SpecificationsOptions Projection dimensions calculation methods List of compatible signals Connector pin wiringAppendix Trademark acknowledgements DimensionsAvertissement Précautions de sécuritéNe pas obstruer les orifices d’entrée et de sortie d’air Pendant un orage, ne pas toucher le projecteur ou le câbleNe pas placer d’objets lourds sur le projecteur Utiliser uniquement les piles spécifiéesAvant l’utilisation Avertissements concernant l’installationPropos de l’écran Propos de la lampeMéthode de remplacement du bloc de lampe Remplacement du bloc de lampeCouper l’alimentation électrique